This guide covers assembly and flight setup for the Premier Astro Star Kite - Rainbow. Follow the steps to set the spreader rods, tension the sails, attach the flying line, and launch.
Applies to: Astro Star Kite - Rainbow. See the 1 products this guide covers.
Specifications
| Model | Size (W x L) | Wind range | Line | Frame | Fabric |
|---|---|---|---|---|---|
| Astro Star Kite - Rainbow | 44 x 35 in. / 112 x 86 cm. | 7 ~ 20 mph | Includes 300 ft. 50 lb. Test Line & Winder | Fiberglass | Ripstop Polyester |
Assembly
Step 1: Lay out the kite
Unroll kite and lay out so that all Sails overlap to one side of Spine Rod. (diagram A)
The Spine Rod runs along one side of the kite, and all Sails overlap to one side of the Spine Rod. The Vinyl Connectors are grouped together at the pointed end.

Step 2: Insert the first spreader rod
Insert one end of a Spreader Rod into the end of the first Vinyl Connector, making sure the Sail remains straight and does not become twisted. (diagram B)
Use the open end of the Vinyl Connector at the end of the sail point. The Spreader Rod enters the connector in the direction shown by the arrow.

Step 3: Continue around the kite
Insert other end of the Spreader Rod into end of the next Vinyl Connector. Continue this process all the way around the kite, making sure Spreader Rods are seated as deeply as possible in Vinyl Connectors. (diagram C)
Each Spreader Rod connects one Vinyl Connector to the next. Work around the kite until the rods form the outside edges between the sail points.

Step 4: Tension the sails
After inserting the last Spreader Rod, tension the Sails by grasping the Spine Rod and pulling on Tension Cord. Lock into place with Tensioning Beads. (diagram D)
The Tensioning Beads are on the Tensioning Cord at the edge of the kite. After the cord is pulled, use the beads to hold the tension in place.

Step 5: Connect the flying line
Connect flying line to 3-point bridle. Your Astro Star is now ready to fly!
The flight instructions refer to the flying line attachment point as the Tow Loop.
Flight instructions
Step 1: Tie on the flying line
Tie flying line to Tow Loop.
Connect the flying line to the 3-point bridle.
Step 2: Have a friend hold the kite
Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.
Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.
Step 3: Release and pull in line
As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.
Step 4: Let out more line
Slowly let out more line as the kite flies upward.
Before you fly
- Recommended line: 80 LB TEST LINE.
- Optimum wind conditions for Astro Star: 7 ~ 20 mph.
- Note: Wind conditions aloft may vary considerably from those found near ground level.
Beaufort wind scale
| Wind [M.P.H.] | Scale | Description |
|---|---|---|
| 0 | Calm | smoke rises vertically |
| 1, 2, 3 | Light Air | Direction of wind shown by smoke, but not by wind vanes |
| 4, 5, 6, 7 | Light Breeze | Wind felt on face, leaves rustle, ordinary vane moves |
| 8, 9, 10, 11, 12 | Gentle Breeze | Leaves and small twigs in constant motion; wind extends light flag |
| 13, 14, 15, 16, 17, 18 | Moderate Breeze | Raises dust and loose paper; small branches move |
| 19, 20, 21, 22, 23, 24 | Fresh Breeze | Small trees & leaves begin to sway; crested wavelets form on inland water |
| 25, 26, 27, 28, 29, 30 | Strong Breeze | Large branches in motion; utility wire whistle; windows rattle |


Astro Star Kite - Rainbow
Share:
Airplane Spinner - Civilian Assembly Instructions
Ball Spinner Assembly Instructions