This guide covers assembly of the B&O Passenger Car Spinner. Connect the strut assembly, install the spinner wheels, and set the completed spinner on its support pole.

Applies to: B&O Passenger Spinner. See the 1 products this guide covers.

Product specs

Product Size (W x L) Spinner platform Spinner theme
B&O Passenger Spinner 34 in. x 20 in. Vehicle Train

Assembly

Step 1: Connect the strut sections

The Strut Assembly of your B&O Passenger Car spinner is shipped in three sections. Connect Center Rods of the Rear Strut Assembly and the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)

In Diagram A, the Rear Strut Assembly is on the left, the Center Strut Assembly is in the middle, and the Front Strut Assembly is on the right. The arrows point the rear and front center rods inward toward the center rod of the center strut assembly.

B&O Passenger Car Spinner rear, center, and front strut assemblies being joined
Diagram A: Connect the rear and front strut assemblies to the center strut assembly.

Step 2: Insert the strut assembly into the body sleeve

Open Velcro straps and insert completed Strut Assembly into bottom of B&O Passenger Car Body Sleeve as shown. Make sure all internal struts connect to the Strut Assembly. Reclose Velcro straps. (diagram B)

The B&O Passenger Car Body Sleeve is above the completed strut assembly, and the arrows show the strut assembly moving up into the bottom of the body sleeve. When finished, the completed internal strut assembly should have all parts connected as shown.

B&O Passenger Car Spinner strut assembly inserted into the body sleeve
Diagram B: Insert the completed strut assembly into the B&O Passenger Car Body Sleeve.
B&O Passenger Car Spinner completed internal strut assembly in the body
Completed internal strut assembly. Make sure all parts connect as shown.

Step 3: Attach a spinner axle at the rear

Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of B&O Passenger Car Body. Tighten the knob on the "T" Joint to hold the Axles to the Struts. (diagram C)

The spinner axle sits below the B&O Passenger Car Body on the rear strut assembly. The knob is on the "T" Joint, which holds the axle to the struts after it is tightened.

B&O Passenger Car Spinner axle sliding onto the rear strut assembly at the T joint
Diagram C: Slide the Spinner Axle onto the Strut Assembly, then tighten the knob on the "T" Joint.

Step 4: Install the first two spinner wheels

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of B&O Passenger Car should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)

The two spinner wheels go on the same spinner axle under the passenger car body. The axle cap goes on the uncapped end after both wheels are on the axle and the wheel directions have been checked.

B&O Passenger Car Spinner wheels on one axle with the axle cap at the end
Diagram D: Slide Spinner Wheels onto Spinner Axle, then hammer Axle Cap onto end.

Step 5: Assemble the front spinner

Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble the front Spinner.

Use the remaining spinner axle and the remaining two spinner wheels for the front spinner. Follow the same wheel-direction note from Step 4.

Step 6: Set the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed B&O Passenger Car Spinner into ferrule on top of Support Pole. (diagram E)

The ferrule is at the top of the support pole, while the non-ferruled end goes into the ground stake. The completed B&O Passenger Car Spinner sits above the support pole with its upper pole section inserted into that ferrule.

Tip: Spinner Wheels on same side of B&O Passenger Car should spin in same direction after assembly.

B&O Passenger Car Spinner set onto a support pole in a ground stake
Diagram E: Insert the support pole into the ground stake and set the completed spinner into the ferrule.

Care note

Please note: Although your B&O Passenger Car Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

B&O Passenger Car Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.