This guide covers assembly of the Premier Fokker Tri-Plane Airplane Spinner. This guide follows the manual steps for installing the wings, landing gear, stabilizer, propeller spinner and support pole.

Applies to: Airplane Spinner - Fokker Tri-Plane. See the 1 products this guide covers.

Specifications

Model Spinner platform Size (W x L)
Fokker Tri-Plane Airplane Spinner Airplane 30 in. x 33 in.

Parts

Fokker Tri-Plane Airplane Spinner parts including fuselage, wings, pole, stake, propeller, struts and guns
Parts overview.
  1. Plane Fuselage x 1
  2. Wing x 3
  3. Support Pole x 1
  4. Spinner Propeller x 1
  5. Stabilizer Cross Strut x 1
  6. Ground Stake x 1
  7. Landing Gear Wing x 1
  8. Machine Guns x 1
  9. Landing Gear Struts x 2

Assembly

Step 1: Insert the landing gear struts

Insert the 2 Landing Gear Struts into the Landing Gear Sleeves. They should cross each other and form an “X”. (diagram A)

The two Landing Gear Struts angle across the fuselage from opposite sides. When you install them, they cross over each other as shown and make the “X” shape called out in the manual.

Fokker Tri-Plane Airplane Spinner landing gear struts crossing through the fuselage
Diagram A: Landing Gear Struts form an X.

Step 2: Install the middle and top wings

Slide the Middle Wing onto the Middle Wing Support Rod located in front of the pilot. Tighten the “T” Thumb Screw onto the Support Rod. Insert the Landing Gear Struts into the Diagonal Plastic Fittings on either side of the wing. Slide the Top Wing onto the tall Top Wing Support Rod located just in front of the Middle Wing Support Rod. Tighten the “T” Thumb Screw under the Top Wing onto the Support Rod. Fasten the Wing Supports attached to the top of the Middle Wing to the Velcro tabs underneath either side of the Top Wing. Please note that the black binding on the wings always faces the rear of the plane. (diagram B)

The Middle Wing Support Rod is the shorter vertical rod in front of the pilot, and the Top Wing Support Rod is the taller rod just in front of it. The Wing Supports rise from the Middle Wing to the Velcro tabs underneath the Top Wing.

Fokker Tri-Plane Airplane Spinner middle and top wings with support rods, thumb screws and Velcro tabs
Diagram B: Middle Wing, Top Wing and Wing Supports.

Step 2: Join the bottom wing at the main fuselage hub

Insert the Aluminum Ferrule attached to the Internal Wing Strut of the Right Wing through the square opening of the Main Fuselage Hub. Then insert the Left Wing’s Internal Wing Strut into the Aluminum Ferrule, which is inside the square channel of the Main Fuselage Hub. Secure the wings to the fuselage with the Velcro tabs on both the top and bottom of the Left and Right Wings. (diagram C & D)

The Bottom Wing slides into the Main Hub, with the Internal Wing Struts meeting inside the square channel. The Velcro tabs are on both sides of the hub on the top and bottom surfaces of the Left and Right Wings.

Fokker Tri-Plane Airplane Spinner bottom wing sliding into the main hub
Diagram C: Bottom Wing slides into Main Hub.
Fokker Tri-Plane Airplane Spinner main fuselage hub with aluminum ferrule and internal wing struts
Diagram D: Main Fuselage Hub and Internal Wing Struts.

Step 3: Insert the landing gear wing

Insert the Landing Gear Wing into the plastic fittings in between the landing gear wheels. Press firmly against the wheels to secure the Landing Gear Wing. (diagram E)

The Landing Gear Wing sits in the space between the landing gear wheels. Move it up into the fittings between the wheels.

Fokker Tri-Plane Airplane Spinner landing gear wing and machine guns placement
Diagram E: Landing Gear Wing and Machine Guns.

Step 4: Fasten the machine guns

Fasten the Machine Guns to the Velcro located on top of the Middle Wing. (diagram E)

The Velcro tab is on top of the Middle Wing, above the fuselage near the pilot. Place the Machine Guns onto that Velcro tab.

Step 3: Insert the stabilizer strut

Insert the Stabilizer Strut into the Stabilizer Sleeves located underneath the stabilizer. Guide the Stabilizer Strut through the Fuselage Stabilizer Hole and to the other side. Then slide the Stabilizer Strut through the other sleeve on the other side of the stabilizer. (diagram F)

The Stabilizer Sleeve is underneath the stabilizer, and the strut passes through the Fuselage Stabilizer Hole before going into the sleeve on the other side. The Internal Fuselage Strut sits inside the tail area near the hole.

Tip: You may have to shift the Fuselage Stabilizer Hole slightly to line up the stabilizer strut through the hole. Shifting the Fuselage Stabilizer Hole can be accomplished by grabbing the main fuselage hub and moving the internal fuselage strut.

Fokker Tri-Plane Airplane Spinner stabilizer strut through sleeve and fuselage stabilizer hole
Diagram F: Stabilizer Strut through the stabilizer.

Step 5: Install the Spinner Propeller

Remove the plastic end cap and spacers from the Engine Cowling Strut and slide the Spinner Propeller onto the strut. Put the spacers and end cap back onto the Engine Cowling Strut to secure the spinner in place. (diagram G)

The spinner slides onto the Engine Cowling Strut after the end cap and spacers have been removed. After the spinner is on the strut, the spacers and end cap go back on to hold it in place.

Fokker Tri-Plane Airplane Spinner propeller spinner sliding onto the engine cowling strut
Diagram G: Propeller Spinner installation.

Step 5: Mount the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Fokker Tri-Plane Spinner into ferrule on top of Support Pole. (diagram H)

The Support Pole stands in the Ground Stake with its ferrule at the top. The completed Fokker Tri-Plane Spinner lowers onto the ferrule on top of the Support Pole.

Fokker Tri-Plane Airplane Spinner mounted on the support pole and ground stake
Diagram H: Ground Stake and Support Pole.

Care and weather note

Please note: Although your Airplane Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Fokker Tri-Plane Airplane Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.