This guide covers assembly and basic flight instructions for the Giant Hespeler Dragon kite. The kite is the Large Hespeler Dragon Diamond.

Applies to: Giant Hespeler Dragon. See the 1 products this guide covers.

Specs

Model Size (W x L) Wind range Line Frame
Giant Hespeler Dragon 156 in. x 99 in. (396 x 251 cm.) w/ 236 in. Banner 6 ~ 18 mph 250 lb. Test Line Recommended Excel Carbon

Assembly

Step 1: Unroll the kite

Unroll kite and lay out flat facedown.

Assemble the kite face down. Keep the kite flat so the spine area, sail loops and pockets can be used as shown in the assembly diagrams.

Step 2: Insert the lower spine strut

Insert Lower Spine Strut into pre-inserted Upper Spine Strut at ferrule. Make sure the Lower Spine Strut goes through the Velcro Pocket Sleeve at the bottom of the spine, Lower Bridle Attachment Point and Sail Loop. (diagram A and B)

The Lower Spine Strut runs along the center spine toward the ferrule. Near the bottom of the spine, it passes through the Velcro Pocket Sleeve, the Lower Bridle Attachment Point and the Sail Loop.

Giant Hespeler Dragon spine struts, sail loop, bridle point, lower stiffener and pockets
Diagram A: Spine struts and lower body stiffener positions.
Giant Hespeler Dragon lower spine strut through sleeve, bridle point, sail loop and ferrule
Diagram B: Lower Spine Strut path.

Step 3: Fit and close the spine

Make sure top of assembled Spine Strut is fit snugly into pocket at top of kite body and tighten and close Velcro Pocket at bottom of kite body. (diagram C)

The top pocket is at the head of the kite body. At the bottom of the kite body, the Velcro Pocket Sleeve closes around the end of the spine.

Tip: Fold Velcro up over end of Spine until Spine is taut on the Sail.

Giant Hespeler Dragon Velcro pocket sleeve and cross strut positions
Diagrams C and D: Velcro pocket and cross struts.

Step 4: Slide in the lower body stiffener

Slide Lower Body Stiffener underneath Lower Spine Strut and into pockets at both edges of lower kite body. (diagram A)

The Lower Body Stiffener runs across the lower kite body. Its ends go into the pockets at both edges of the lower kite body.

Step 5: Insert the in-board cross struts

Insert In-Board Cross Strut into Dihedral on Spine Strut (go through Sail Loop.) Repeat other side. (diagram D)

The In-Board Cross Struts extend out from the center spine across the sail. Each one passes through a Sail Loop before reaching outward toward the edge of the kite.

Step 6: Insert the rear cross strut

Insert Rear Cross Strut into Fitting on the In-Board Cross Strut. (diagram E)

The Rear Cross Strut spans across the back of the cross-strut assembly. Its ends go into the fittings on the In-Board Cross Struts.

Tip: Make sure the Cross Strut and all rods are seated all the way into the fittings.

Giant Hespeler Dragon rear cross strut inserted into fittings on in-board cross struts
Diagram E: Rear Cross Strut fittings.

Step 7: Connect and tension the out-board cross struts

Insert other end of the In-Board Cross Strut into the Ferrule end of the Out-Board Cross Strut. Hook Arrow Nock ends of Out-Board Cross Struts onto Bead Tensioners at edges of kite body and tension as needed. The String and Bead of the Bead Tensioner goes through slit in Nock. (diagram F)

The Arrow Nock is at the kite-edge end of the Out-Board Cross Strut. The Bead Tensioner passes through the Nock Slit at that end.

Giant Hespeler Dragon arrow nock, nock slit and bead tensioner at the out-board cross strut
Diagram F: Arrow Nock and Bead Tensioner.

Step 8: Pull the bridle through and attach the line

Make sure Bridle is pulled completely through front of sail, attach line to Bridle, and your Dragon Diamond is ready to fly!

The Tow Loop is at the end of the bridle lines. Attach the flying line at the bridle after the bridle is pulled through the front of the sail.

Giant Hespeler Dragon bridle and tow loop for tying the flying line
Diagram G: Bridle and Tow Loop.

Flight instructions

Step 1: Tie on the flying line

Tie flying line to Tow Loop. (diagram G)

The Tow Loop sits at the point where the bridle lines meet. Tie the flying line to that loop.

Step 2: Position the kite downwind

Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.

Your friend is downwind from you, holding the kite with the head pointed towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out line

Slowly let out more line as the kite flies upward.

Recommended line

250 lb. Test Line Recommended.

250 lb. Test Line is recommended, and line is not included.

Beaufort scale and optimum wind conditions

Scale Wind [M.P.H.] Description
CALM 0 smoke rises vertically
LIGHT AIR 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
LIGHT BREEZE 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
GENTLE BREEZE 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
MODERATE BREEZE 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
FRESH BREEZE 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
STRONG BREEZE 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle
Giant Hespeler Dragon Beaufort wind chart with Large Dragon Diamond range
Optimum wind conditions for Large Dragon Diamond.

Wind range for Giant Hespeler Dragon: 6 ~ 18 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Giant Hespeler Dragon Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.