This guide covers assembly of the Premier School Bus Spinner. It applies to the 29 in. x 16 in. School Bus Spinner.

Applies to: 29 in. School Bus Spinner. See the 1 products this guide covers.

Assembly

Step 1: Connect the strut assemblies

The Strut Assembly of your School Bus spinner is shipped in three sections. Connect Center Rods of the Rear Strut Assembly and the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)

Use the Rear Strut Assembly on one side of the Center Strut Assembly and the Front Strut Assembly on the other side, as shown. The center rods slide inward toward the Center Strut Assembly.

School Bus Spinner rear, center, and front strut assemblies connecting
A: Connect the rear and front strut assemblies to the center strut assembly.

Step 2: Insert the strut assembly into the body sleeve

Open Velcro straps and insert completed Strut Assembly into bottom of School Bus Body Sleeve as shown. Make sure the Internal Body Strut is connected to the Strut Assemblies. Reclose Velcro straps. (diagram B)

The School Bus Body Sleeve is along the bottom of the bus body, and the completed Strut Assembly goes up into it. The Internal Body Strut sits inside the bus body and connects to the strut assemblies.

School Bus Spinner body sleeve with completed strut assembly and internal body strut
B: Insert the completed strut assembly into the School Bus Body Sleeve.

Step 3: Attach the rear spinner axle

Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of School Bus Body. Tighten the knob on the "T" Joint to hold the Axles to the Struts. (diagram C)

The Spinner Axle is positioned at the rear of the School Bus Body with the “T” Joint below the body. Slide the Spinner Axle onto the Strut Assembly first, then tighten the knob on the “T” Joint.

School Bus Spinner rear spinner axle sliding onto the strut assembly
C: Slide the Spinner Axle onto the Rear Strut Assembly and tighten the knob on the “T” Joint.

Step 4: Install the rear spinner wheels

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of School Bus should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)

The two Spinner Wheels sit on the same Spinner Axle with the School Bus Body between them. The uncapped end of the Spinner Axle receives the Axle Cap after the wheels are in place.

School Bus Spinner wheels on one axle with axle cap and opposite spin arrows
D: Slide Spinner Wheels onto the Spinner Axle, then hammer the Axle Cap onto the end.
School Bus Spinner on support pole and ground stake with wheels spinning the same direction
E: Mount the completed School Bus Spinner on the Support Pole.

Step 5: Assemble the front spinner

Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble front Spinner.

After this step, the School Bus has Spinner Wheels at both the rear and front wheel positions. The Spinner Wheels on the same side of the School Bus should spin in the same direction after assembly.

Step 6: Mount the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed School Bus Spinner into ferrule on top of Support Pole. (diagram E)

The Support Pole fits down into the Ground Stake, and the ferrule is at the top of the Support Pole. The completed School Bus Spinner drops into the ferrule above the Support Pole.

Care and weather note

Please note: Although your Accent School Bus Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

School Bus Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.