This guide covers assembly and flying for Premier's 52 in. Travel Diamond Kite designs. It applies to the Hot Tronic, Orbit Tron, and Tecmo Tron versions.

Applies to: 52 in. Travel Diamond Kite - Hot Tronic, Orbit Tron, and Tecmo Tron. See the 3 products this guide covers.

Kite specs

Models Size (W x L) Wind range Fabric Frame Line
Hot Tronic, Orbit Tron, Tecmo Tron 53 x 53 in. / 134.6 x 134.6 cm. 6 ~ 16 mph Ripstop Polyester Fiberglass SnapRod Yo-Yo Winder with 300 ft. 50 lb. Test line

Assembly overview

Assembly of your Travel Diamond is a snap! All Struts on your Travel Diamond are attached to the frame and fully Shock Corded. This eliminates loose pieces and assembly guesswork.

Assembly

Step 1: Push together the corded struts

Push together the Corded Struts. Make sure the Struts are fully seated in Ferrules.

Slide the strut end straight into the ferrule, following the direction shown by the arrow. The shock cord runs between the strut sections, and the struts should sit fully in the ferrules.

52 in. Travel Diamond strut sliding into the ferrule with shock cord shown
Diagram A: Corded struts and ferrule

Step 2: Insert the cross struts

Insert Cross Struts into the Center Fitting. The arms on the Center Fitting should be pointing up (away from the Sail).

Insert one cross strut from each side into the center fitting. When the center fitting is turned correctly, the arms point out away from the sail and the sail bows in the opposite direction from the bridle. If the arms point inwards towards the sail, the sail bows out in the same direction as the bridle; this is incorrect.

52 in. Travel Diamond cross struts inserted into the center fitting with arms up
Diagram B: Cross struts into the center fitting
52 in. Travel Diamond correct and incorrect sail bow direction at the bridle
Diagram C: Correct and incorrect center fitting orientation

Step 3: Close the spine tensioning pocket

This kite includes a Spine Tensioning Pocket. When closing the pocket, make sure that the Spine is taut on the Sail.

The Velcro pocket is at the end of the spine. Fold Velcro up over the end of the spine until the spine is taut on the sail.

52 in. Travel Diamond spine and Velcro pocket folded up to tension the sail
Diagram D: Spine tensioning pocket

Step 4: Check the tow point

Your kite's Tow Point has been set at the factory on the Factory Mark. This setting is best for most all winds. Please note adjustments can be made on your kite for different wind conditions.

Use the labeled directions toward top of Kite and toward bottom of Kite and the Tow Loop. For flying in low winds, the diagram marks a position on the line toward top of Kite. For flying in high winds, the diagram marks a position on the line toward bottom of Kite.

52 in. Travel Diamond tow loop with factory mark and high- and low-wind settings
Diagram E: Tow point factory mark and wind adjustments

Step 5: Remove the rubber band from the tail

Take rubber band off Tail before flying.

Flying

Step 1: Attach the flying line

Attach Flying Line to Tow Loop.

Use the tow loop shown on the bridle at the tow point. The factory set mark is the normal tow point setting before any wind-condition adjustment is made.

Step 2: Position a helper downwind

Have a friend stand about 75 feet downwind from you and hold the Kite with its nose pointed towards the sky.

Your friend should be downwind from you while holding the kite with its nose pointed towards the sky.

Step 3: Release the kite

As the wind catches the Kite, signal your friend to release it while you steadily pull in Line until the kite is aloft.

Step 4: Let the kite climb

As the Kite flies upward, slowly release more Line.

Beaufort scale and wind note

Wind description Wind [M.P.H.]
Calm 0
Light Air 1, 2, 3
Light Breeze 4, 5, 6, 7
Gentle Breeze 8, 9, 10, 11, 12
Moderate Breeze 13, 14, 15, 16, 17, 18
Fresh Breeze 19, 20, 21, 22, 23, 24
Strong Breeze 25, 26, 27, 28, 29, 30
52 in. Travel Diamond Beaufort wind chart with the kite wind range marked
Beaufort Scale: Optimum wind conditions for 52" Travel Diamond Kite

Use the Beaufort Scale chart for optimum wind conditions for 52" Travel Diamond Kite. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

52 in. Travel Diamond Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.