This guide covers assembly and basic flying for the Premier 80 in. Travel Delta Kite. It shows how to assemble the leading edge struts, spine, cross strut, tails and flying line.
Applies to: 80 in. Travel Delta Kite - Red & Black. See the 1 products this guide covers.
Specs
| Model | Size | Wind range | Line | Frame | Fabric |
|---|---|---|---|---|---|
| 80 in. Travel Delta Kite | 80 x 41 in. / 203.2 x 104.1 cm. | 5 ~ 18 mph | Includes Yo-Yo Winder with 300 ft. 90 lb. Test line | Fiberglass SnapRod | Ripstop Polyester |
Assembly
Step 1: Assemble the leading edge struts
Unfold your kite. Assemble the Leading Edge Struts. Each Leading Edge Strut is made up of 2 Shock Corded pieces. They are already hidden inside the Leading Edge Sleeve. There is an opening on the side of the Sleeve to access these Struts. At the end of the Lower Strut is a ferrule that the upper strut slides into. Slide the two pieces together and make sure they are fully seated in the ferrule. Make sure each assembled strut is fully contained within the Sleeve and not protruding through the opening. (diagram A and B)
Reach the Shock Corded Struts through the Leading Edge Sleeve Opening. The space in the sleeve at the nose is empty and contains no struts, and the bottom of each strut ends at the lower wing tip area.


Step 2: Put together the other shock corded struts
Put together the two other Shock Corded Struts, making sure the Struts are fully seated in their Ferrules. (diagram C)
The shorter strut is labeled Cross Strut, and the longer strut is labeled Spine. Each strut section slides toward its ferrule to join the two pieces.

Step 3: Insert the spine
The long Strut is the Spine. Insert it into the Spine Pockets. This kite includes a Velcro Spine Tensioning Pocket. When closing the pocket, make sure that the Spine is taut on the Sail. (diagram D and E and F)
The Spine runs from the top Spine Pocket down to the Velcro Spine Pocket at the lower center of the sail. The end of the Spine sits inside the Velcro Pocket before the pocket is closed.



Step 4: Insert the cross strut
The shorter Strut is the Cross Strut. Insert it into the Cross Strut Pockets. (diagram F)
The Cross Strut runs across the kite, with its ends going into the Cross Strut Pockets at each side. It crosses the Spine at the center of the sail.
Step 5: Attach the tails and flying line
Attach Tails to Wing Tip Loops. Attach the Flying Line to the Tow Point. (diagram G)
The Wing Tip Loops are at the two lower wing tips, with one Tail attached to each loop. The Tow Point is on the Keel on the front of the Kite.

Flying
Step 1: Position the kite downwind
Have a friend stand about 75 feet downwind from you and hold the Kite with its nose pointed towards the sky.
You hold the line while your friend holds the Kite about 75 feet downwind. Keep the nose pointed towards the sky.
Step 2: Release the kite
As the wind catches the Kite, signal your friend to release it while you steadily pull in Line until the Kite is aloft. As the Kite flies upward, slowly release more Line.
Wind conditions
| Beaufort scale condition | Wind [M.P.H.] |
|---|---|
| Calm | 0 |
| Light Air | 1, 2, 3 |
| Light Breeze | 4, 5, 6, 7 |
| Gentle Breeze | 8, 9, 10, 11, 12 |
| Moderate Breeze | 13, 14, 15, 16, 17, 18 |
| Fresh Breeze | 19, 20, 21, 22, 23, 24 |
| Strong Breeze | 25, 26, 27, 28, 29, 30 |

Best wind for 80 in. Travel Delta Kite: 5 ~ 18 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.



80 in. Travel Delta Kite - Red & Black
Share:
7 ft. Shark Kite Assembly Instructions
9 ft. Delta Kite Assembly Instructions