This guide covers assembly for the Premier Accent Tractor Spinner. It applies to the 29 in. x 21 in. Old Tractor Spinner in green and red.

Applies to: 29 in. Old Tractor Spinner - Green and Red. See the 2 products this guide covers.

Assembly

Step 1: Connect the strut assembly

The Strut Assembly of your Tractor spinner is shipped in three sections. Connect Center Rods of the Rear Strut Assembly and the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)

The Rear Strut Assembly and Front Strut Assembly are the outside sections, and the Center Strut Assembly is the middle section. The arrows point the center rods inward toward the Center Rod of the Center Strut Assembly.

Premier Accent Tractor rear, center and front strut assemblies connecting
Diagram A: Connect the three Strut Assembly sections.

Step 2: Insert the completed strut assembly

Open Velcro straps and insert completed Strut Assembly into bottom of Tractor Body Sleeve as shown. Make sure the Internal Body Strut is connected to the Strut Assemblies. Reclose Velcro straps. (diagram B)

The completed Strut Assembly moves up into the bottom of the Tractor Body Sleeve. The Internal Body Strut is at the upper body area and should be connected to the Strut Assemblies before the Velcro straps are closed.

Premier Accent Tractor strut assembly inserted into the tractor body sleeve
Diagram B: Insert the completed Strut Assembly into the Tractor Body Sleeve.

Step 3: Attach the rear spinner axle

Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of Tractor Body. Tighten the knob on the "T" Joint to hold the Axles to the Struts. (diagram C)

The Spinner Axle runs sideways under the back of the Tractor Body. Slide the "T" Joint onto the Strut Assembly first, then tighten the knob on the "T" Joint.

Premier Accent Tractor spinner axle sliding onto the rear strut assembly
Diagram C: Attach the Spinner Axle to the Strut Assembly.

Step 4: Install two spinner wheels on the rear axle

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of Tractor should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)

The two Spinner Wheels on the same axle sit on opposite sides of the Tractor Body. Check the wheel directions before the second Axle Cap is put into place; wheels on the same axle should spin in opposite directions.

Premier Accent Tractor spinner wheels and axle cap on one axle
Diagram D: Slide Spinner Wheels onto the Spinner Axle and add the Axle Cap.

Step 5: Assemble the front spinner

Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble front Spinner.

Use the second Spinner Axle with the two remaining Spinner Wheels. Keep the same wheel-direction rule from Step 4 for the front Spinner.

Step 6: Mount the tractor on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Tractor Spinner into ferrule on top of Support Pole. (diagram E)

The Support Pole fits into the Ground Stake, and the ferrule is at the top of the Support Pole. The Upper Pole Section of the completed Tractor Spinner goes down into that ferrule. After assembly, Spinner Wheels on the same side of the Tractor should spin in the same direction.

Premier Accent Tractor mounted on support pole and ground stake
Diagram E: Insert the completed Tractor Spinner into the Support Pole.

Care and weather

Please note: Although your Accent Tractor Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Accent Tractor Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.