This guide covers assembly for Premier Airplane Spinners. For these designs, use the same basic steps for the wings, stabilizer, propeller and support pole.

Applies to: Bombs Away, Hell Cat, ME109, P-40 Warhawk, P-51 Mustang and Spitfire Airplane Spinners. See the 6 products this guide covers.

Have the Biplane or Sopwith Camel spinner? See the Biplane Spinner Assembly Instructions.

Models and sizes

Model Size (W x L)
Bombs Away 30 in. x 26.5 in.
Hell Cat 27 in. x 27 in.
ME109 25 in. x 25 in.
P-40 Warhawk 24.5 in. x 23 in.
P-51 Mustang 25 in. x 31 in.
Spitfire 25 in. x 29 in.

Parts shown in the manual

Airplane Spinner parts: fuselage, propeller, struts, support pole and stake
Parts shown in the manual.
  1. Plane Fuselage x 1
  2. Spinner Propeller x 1
  3. Wing Struts x 2
  4. Stabilizer Cross Strut x 1
  5. Support Pole x 1
  6. Ground Stake x 1

Assembly

Step 1: Insert the wing struts

Insert the two Wing Struts through the two openings at the wing tip of one of the wings. Guide them through the inside of the wings. (diagrams A & B)

Use the two openings at the wing tip shown on the bottom of the wing. Both Wing Struts enter from the wing tip and run inside the wing through the wing opening for struts.

Airplane Spinner wing struts entering two openings at the bottom of the wing
Diagram A: Wing Struts at the bottom of the wing.
Airplane Spinner wing opening for struts with one Wing Strut entering
Diagram B: Wing Opening for struts.

Step 2: Pass the struts through the fuselage channels

Pass the struts through the Channel Holes in the fuselage, found underneath the wings and through the Aluminum Channel inside the fuselage. Guide the struts through the inside of the wing to the other wing to the end of the wing tip. This wing tip should be sewn closed, so the struts can not pass through. You may have to shift the Fuselage Channels Holes slightly to guide them through. (diagram C)

Underneath the wings, the struts pass across the fuselage through the Channel Holes and the Aluminum Channel. The arrows show both Wing Struts continuing toward the opposite wing tip, with the Main Fuselage Hub between the channel holes.

Airplane Spinner wing struts passing through fuselage channel holes
Diagram C: Channel Holes and Aluminum Channel.

Insert the stabilizer strut

Insert the Stabilizer Strut into the Stabilizer Sleeves located underneath the stabilizer. Guide the Stabilizer Strut through the Fuselage Stabilizer Hole and to the other side. Then slide the Stabilizer Strut through the other sleeve on the other side of the stabilizer. (diagram E)

The Stabilizer Sleeve is underneath the stabilizer, with a hidden opening at the sleeve end. The Stabilizer Strut passes through the Fuselage Stabilizer Hole and across to the sleeve on the other side.

Tip: You may have to shift the Fuselage Stabilizer Hole slightly to line up the stabilizer strut through the hole. Shifting the Fuselage Stabilizer Hole can be accomplished by grabbing the main fuselage hub and moving the internal fuselage strut.

Airplane Spinner side view with Main Fuselage Hub labeled
Diagram D: Main Fuselage Hub.
Airplane Spinner stabilizer strut entering the stabilizer sleeve and fuselage hole
Diagram E: Stabilizer Strut and Stabilizer Sleeve.

Install the spinner propeller

Remove the wooden end cap and spacer from the propeller axle exiting from the front end of the fuselage. Slide on the Spinner Propeller. Place the Spinner Propeller onto the propeller axle, then replace the spacer and the end cap. (diagram F)

The propeller axle exits from the front end of the fuselage. The Spinner Propeller goes onto that axle, and the spacer and end cap are replaced after the propeller is in place.

Tip: Hell Cat and Bombs Away: this is a white, wooden end cap.

Airplane Spinner propeller, spacer and end cap aligned with the front axle
Diagram F: Spinner Propeller on the propeller axle.

Mount the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Airplane Spinner into ferrule on top of Support Pole. (diagram G)

The non-ferruled end of the Support Pole goes into the Ground Stake. The completed spinner’s Upper Pole Section goes into the ferrule on top of the Support Pole.

Airplane Spinner mounted on the Support Pole and Ground Stake
Diagram G: Support Pole and Ground Stake.

Care note

Although your Airplane Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.