This guide covers assembly, launching, flying, safety and wind information for Premier Butterfly Kites. It applies to the Monarch, Rainbow Orbit and Tie Dye designs.
Applies to: Butterfly Kite - Monarch, Rainbow Orbit and Tie Dye. See the 3 products this guide covers.
Specifications
| Designs | Size | Wind range | Line | Fabric | Frame |
|---|---|---|---|---|---|
| Monarch, Rainbow Orbit, Tie Dye | 52 x 37 in. / 132 x 94 cm. | 5 ~ 18 mph | Includes 300 ft. 50 lb. Test Line & Winder | Ripstop Polyester | Fiberglass |
Assembly
Step 1: Unroll the kite
Remove Butterfly from carrying sleeve and unroll it.
You can see the center spine, bridle, tow point, tubing and spar pockets labeled in the diagram.

Step 2: Insert the tail spar
Insert short wooden tail spar into the tubing located on the spine and spar pockets on the tail.
The tubing is on the center spine near the lower tail area. The spar pockets are at the tail ends.
Step 3: Insert the cross spar
Now insert the cross spar into the plastic dihedral and insert opposite ends into the retaining pockets on the wingtips.
The cross spar runs across the wings through the dihedral at the spine. Its opposite ends go into the pockets at the left and right wingtips.
Step 4: Attach the flying line
Attach a 50 lb. test line to the tow point on the bridle and you are ready to fly.
The bridle leads to the tow point shown to one side of the kite. Attach the flying line at that tow point.
Launching
Step 1: Launch from your hand
This kite may be flown out of your hand. Simply play out line gradually, keeping enough pressure on the line to prevent the kite from dropping.
Let the line out a little at a time while keeping pressure on the line.

Step 2: Fly at 100 feet or more
It is best to fly at 100 feet or more to allow the kite room to recover should it encounter turbulent or gusty winds. The addition of a tail will help stabilize the kite in strong wind conditions. Attach this to the bottom of the center spine.
If you add a tail, the attachment point is the bottom of the center spine.
Step 3: Use an assisted launch if needed
If you are a novice or have trouble self launching, have a friend stand about 75 feet downwind from you and hold the kite with its nose pointed towards the sky. As the wind catches the kite, signal your friend to release the kite while you pull in the line with long steady pulls. As the kite flies upward, slowly let out more line.
Your friend holds the kite downwind with the nose pointed toward the sky. You hold the line and pull with long steady pulls as the kite is released.
Flying
Step 1: Recover from a dive
If your kite should go into a dive, immediately let out a little line and the kite will swing out of the dive.
Step 2: Keep the kite aloft in a lull
If the kite drops during a lull in the wind, pull in the line to keep it aloft.
Safety measures
Select a wide open area to fly your kite. Avoid areas with buildings, trees, electrical lines, and crowds. Never fly your kite near power lines and busy streets or over spectators and crowds.
Wind conditions
| Wind [M.P.H.] | Beaufort scale | Description |
|---|---|---|
| 0 | Calm | smoke rises vertically |
| 1, 2, 3 | Light Air | Direction of wind shown by smoke, but not by wind vanes |
| 4, 5, 6, 7 | Light Breeze | Wind felt on face, leaves rustle, ordinary vane moves |
| 8, 9, 10, 11, 12 | Gentle Breeze | Leaves and small twigs in constant motion; wind extends light flag |
| 13, 14, 15, 16, 17, 18 | Moderate Breeze | Raises dust and loose paper; small branches move |
| 19, 20, 21, 22, 23, 24 | Fresh Breeze | Small trees & leaves begin to sway; crested wavelets form on inland water |
| 25, 26, 27, 28, 29, 30 | Strong Breeze | Large branches in motion; utility wire whistle; windows rattle |

Optimum wind conditions for Butterfly: 5-18 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.



Butterfly Kite - Monarch
Butterfly Kite - Rainbow Orbit
Butterfly Kite - Tie Dye
Share:
Box Kite Assembly Instructions
Butterfly Spinner Assembly Instructions