This guide covers assembly for Premier Carousel Spinner designs. It shows how to attach the decorative elements, assemble the axle and support rods, and set the spinner on the ground stake.

Applies to: Carousel Spinner - Fish, Hummingbirds and Rubber Ducks. See the 3 products this guide covers.

Specs

Design Size (W x L)
Fish 59 in. x 28 in.
Hummingbirds 59 in. x 28 in.
Rubber Ducks 58 in. x 28 in.

Parts

Carousel Spinner parts including rods, axle, stake, washers, hinge pins and decorative elements
Parts
  1. Ground Stake
  2. Lower Support Rod
  3. Upper Support Rod
  4. 2 Horizontal Rods
  5. Vertical Axle
  6. 2 Washers
  7. 4 Hinge Pins
  8. 2 Decorative Elements (counter-clockwise turning)
  9. 2 Decorative Elements (clockwise turning)

Assembly

Step 1: Attach the decorative elements

Insert the Hinge Pin into Hinge on each Decorative Element to attach it to the Horizontal Rod. Make sure that the Decorative Element is not upside down when you attach it. The spinner will not spin properly if the Decorative Elements are upside down. The Decorative Elements should face opposite directions on the ends of each Horizontal Rod (Diagrams A & B).

Use the two Decorative Elements marked as going on the same horizontal rod for each Horizontal Rod. The diagrams mark TOP, Front, Bottom and Direction of travel so you can keep the Decorative Elements upright and facing opposite directions on the rod.

Carousel Spinner Diagram A showing hinge pin attaching a decorative element to a horizontal rod
Diagram A: Hinge pin and Decorative Element
Carousel Spinner Diagram B showing decorative elements facing opposite directions on a rod
Diagram B: Decorative Elements face opposite directions

Step 2: Install the first hub on the vertical axle

Remove the Vertical Axle Cap from the Vertical Axle. Put a Washer on the Axle. Put the first Hub onto the Vertical Axle so that it sits on top of the Washer. (Diagram C & D)

The washer sits below the first hub on the Vertical Axle. The first hub sits above the washer and stopper (Diagram D).

Carousel Spinner Diagram C with hub, washer, vertical axle and axle cap
Diagram C: First hub, washer and vertical axle
Carousel Spinner Diagram D showing top decoration over the vertical axle cap
Diagram D: Top Decoration and first hub

Step 3: Add the axle cap and top decoration

Put the Vertical Axle Cap on the Vertical Axle. Place the Top Decoration on top of the Axle Cap. (Diagram D)

The Top Decoration sits over the capped top of the Vertical Axle. In the finished position shown, the cap is inside the stitched sleeve pocket of the Top Decoration.

Step 4: Install the second hub and washer

Stick the Axle through the second Hub. Stick the second Washer onto the Axle below the second Hub. (Diagram E & F)

The second hub goes below the first hub on the same Vertical Axle. The second washer sits directly below the second hub, while the first hub remains above its washer and stopper.

Tip: Important Tip: The decorative element will always seek to travel toward the “Short Distance” hinge side of the decorative element.

Carousel Spinner Diagram E showing second hub and washer below the first hub
Diagram E: Second hub and washer
Carousel Spinner Diagram F showing direction of travel and long and short distance from hinge
Diagram F: Direction of travel

Step 5: Assemble the support rods

Stick the Vertical Axle into Upper Support Rod. Stick the Upper Support Rod into the Lower Support Rod (Diagram G). The Vertical Axle will come to rest by an Internal Stop inside the Upper Support Rod. The Vertical Axle is held in place by gravity. For more permanent installations you may glue the Vertical Axle into the Upper Support Rod.

The Vertical Axle enters the top of the Upper Support Rod. The Lower Support Rod connects below the Upper Support Rod, and the internal stop is factory set inside the Upper Support Rod.

Carousel Spinner Diagram G showing vertical axle, upper support rod and lower support rod
Diagram G: Support rods

Step 6: Set the spinner on the ground stake

Drive Ground Stake into ground and insert the Support Pole of assembled Carousel Spinner into the Ground Stake. (Diagram H)

The completed Carousel Spinner sits above the Ground Stake with the Lower Support Rod going down into the stake. The Vertical Axle, Upper Support Rod, Lower Support Rod and Ground Stake line up vertically.

Carousel Spinner Diagram H showing assembled spinner above the ground stake
Diagram H: Ground Stake installation

Care note

Please note: It is recommended that you take your Carousel Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Carousel Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.