This guide covers assembly for Premier 25 in. Car Spinners. It applies to the animal, fantasy, bug and seasonal car spinner designs listed below.

Applies to: 25 in. Car Spinners: Turtle, Cat, Dog, Dragon, Frog, Ladybug, Monkey, Scarecrow, Skeleton and Witch. See the 10 products this guide covers.

Product specs

Design Spinner theme Size (W x L)
Turtle Animal 25 in. x 18.75 in.
Cat Animal 25 in. x 18.5 in.
Dog Animal 25 in. x 22 in.
Dragon Fantasy 25 in. x 19 in.
Frog Animal 25 in. x 20.25 in.
Ladybug Bug 25 in. x 19.5 in.
Monkey Animal 25 in. x 19.5 in.
Scarecrow Holiday / Seasonal 25 in. x 20 in.
Skeleton Holiday / Seasonal 25 in. x 18.75 in.
Witch Holiday / Seasonal 25 in. x 20.5 in.

Assembly

Step 1: Insert the body rod

Remove your Car Spinner from the package and unfold the fabric Body. Open the Velcro seam along the bottom of the Car and slide the Body Rod into the head of the fabric Body and firmly insert the bottom of the Body Rod into the top of the Starlock Hub.

The Body Rod runs up into the head area of the fabric Body, with its lower end seated in the top of the Starlock Hub. The Velcro seam is along the bottom of the car body, giving access to the internal strut assembly.

Car Spinner internal strut assembly with body rod, hub, Velcro seam and support pole
Diagram A: Internal strut assembly

Step 2: Attach the support pole

Slide the narrow, plastic tipped end of the Support Pole into Starlock Hub. Push down on the hub until the Support Pole locks into place and can not be removed. Close Velcro Seam. Completed internal Strut Assembly should match Diagram A.

The plastic tip of the Support Pole lines up underneath the Starlock Hub, and the hub is pushed down onto it. When assembled, the Support Pole sits centered below the Starlock Hub inside the car body.

Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Step 3: Install the spinner axles

Slide the Spinner Axles onto the Wheel Strut Assemblies. Tighten knobs on the "T" Joints to hold the Axles to the Struts. (Diagram B)

Each Spinner Axle sits in a "T" Joint at the bottom of a Wheel Strut Assembly. The knob on the "T" Joint tightens against the axle to hold it to the strut.

Car Spinner axle sliding onto the strut assembly and T joint
Diagram B: Spinner Axle and T Joint

Step 4: Add the spinner wheels

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of Car should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams C and D.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (Diagram C)

The Axle Cap goes onto the uncapped end after the wheels are on the Spinner Axle. The arrows show the two wheels on the same axle spinning in opposite directions, while the wheels on the same side of the car spin in the same direction.

Car Spinner wheels on an axle with the axle cap and opposite spin directions
Diagram C: Spinner Wheels and Axle Cap

Step 5: Set the car spinner in the ground stake

Drive Ground Stake into ground. Slide assembled Car Spinner into Ground Stake. (Diagram D)

The Support Pole slides down into the top of the Ground Stake. When finished, the assembled car sits above the stake with the wheels positioned on the car body.

Car Spinner support pole sliding into the ground stake
Diagram D: Ground Stake installation

Care and weather

PLEASE NOTE: It is recommended that you take your Car Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Car Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.