This guide covers assembly and setup for the Premier 29 in. Golf Cart Spinner. The spinner measures 29 in. x 34 in. and is constructed with UV resistant SunTex(TM) fabric.

Applies to: 29 in. Golf Cart Spinner. See the 1 products this guide covers.

Assembly

Step 1: Open the Velcro seam

Remove your Empty Red Golf Cart Spinner from the package. Open the Velcro Seam along the bottom of the Golf Cart.

The Velcro Seam runs along the bottom edge of the golf cart body. Opening it gives access to the inside of the cart for the rods and strut assembly.

Premier Golf Cart Spinner rods 1 and 2 inserted into sleeves with Hub 1 and Velcro Seam
Diagram A: Rod 1 and Rod 2 slide into Sleeve 1 and Sleeve 2 through the Velcro Seam.

Step 2: Slide Rod 1 and Rod 2 into the sleeves

Slide Rod 1 and 2 through the opened Velcro Seam into the corresponding Sleeve 1 and 2 as shown in Diagram A. Push Rod 1 so that it securely fits into the Hub 1 at the top left of the frame structure as shown in Diagram A.

Rod 1 goes up through Sleeve 1 at the left side of the cart body, with Hub 1 at the top left. Rod 2 goes up through Sleeve 2 on the angled front support.

Step 3: Assemble Main Strut A, the Star Lock Hub, and Main Strut B

Identify and align Main Strut A, Star Lock Hub, and Main Strut B according to Diagram B. Insert the Main Strut A rod into the Star Lock Hub horizontal fitting securely. Insert the Main Strut B rod into the Star Lock Hub horizontal fitting securely.

Main Strut A enters the Star Lock Hub from one side, and Main Strut B enters from the other side. When aligned as shown, the Star Lock Hub sits between the two main struts.

Premier Golf Cart Spinner Main Strut A, Main Strut B, Star Lock Hub, and Upper Support Pole
Diagram B: Main Strut A and Main Strut B fit into the Star Lock Hub, which pushes onto the Upper Support Pole.

Step 4: Attach the Upper Support Pole to the Star Lock Hub

Slide the narrow plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and cannot be removed.

The plastic tip of the Upper Support Pole points up into the Star Lock Hub. Push the Star Lock Hub firmly down onto the plastic tip.

Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Step 5: Position the strut assembly inside the fabric

Position the Strut Assembly in between the pieces of fabric and insert Rod 1 into the Hub of Main Strut A as shown in Diagram C.

The Strut Assembly runs across the inside of the cart body. The Hub of Main Strut A sits near Rod 1, with Rod 1 inserted into that hub.

Premier Golf Cart Spinner internal strut assembly with Main Strut A Hub, Rod 3, and Velcro Seam
Diagram C: Completed internal Strut Assembly with Rod 3 and the Velcro Seam.

Step 6: Insert Rod 3 and close the seam

Insert Rod 3 in between the pieces of fabric so that it is positioned at an angle from the bottom corner below the black bumper to just above the Main Strut A Hub. Close Velcro Seam. Completed internal Strut Assembly should match Diagram C.

Rod 3 sits at an angle near the rear bottom corner of the cart body. The completed internal strut assembly is inside the fabric, with the Velcro Seam closed along the bottom.

Step 7: Attach the spinner axles

Slide the Spinner Axles onto the Wheel Strut Assemblies. Tighten Knobs on the “T” Joints to hold the axles to the Struts. (Diagram D)

The “T” Joint is on the Spinner Axle assembly. After the axle slides onto the strut assembly, the knob on the “T” Joint holds it to the strut.

Premier Golf Cart Spinner axle sliding onto the strut assembly with a knob on the T joint
Diagram D: Slide the Spinner Axle onto the Strut Assembly and tighten the knob on the “T” Joint.

Step 8: Install the spinner wheels

Take one of the four Spinner Wheels and slide it on to one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of the Golf cart should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place make sure wheels spin as shown in diagrams E and F.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (Diagram E)

One Spinner Wheel sits on each side of the same Spinner Axle (Diagram E). The Axle Cap goes onto the uncapped end after the wheels are on the axle.

Premier Golf Cart Spinner wheels on an axle with axle cap and opposite spin directions
Diagram E: Spinner Wheels slide onto the Spinner Axle and the Axle Cap is hammered onto the end.

Step 9: Set the spinner on the support pole and ground stake

Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole into the Ground Stake. Insert Upper Pole of assembled Spinner into the ferrule. (Diagram F)

The Lower Support Pole goes into the Ground Stake with the ferrule at the top. The Upper Support Pole from the assembled spinner then fits into the ferrule.

Premier Golf Cart Spinner on Upper Support Pole, ferrule, Lower Support Pole, and Ground Stake
Diagram F: Ground Stake, Lower Support Pole, ferrule, and Upper Support Pole setup.

Care note

It is recommended that you take your Golf Cart Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Golf Cart Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.