This guide covers assembly for the Premier 28 in. Hot Rod Spinner. It shows how to connect the internal strut assembly, add the spinner wheels and mount the completed spinner on its support pole.

Applies to: 28 in. Hot Rod Spinner. See the 1 products this guide covers.

Assembly

Step 1: Connect the strut assembly

The Strut Assembly of your Hot Rod spinner is shipped in three sections. Connect Center Rods of the Rear Strut Assembly and the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)

The Rear Strut Assembly is on the left, the Center Strut Assembly in the middle, and the Front Strut Assembly on the right. The arrows point the rear and front center rods inward toward the Center Strut Assembly; when connected, the rods form one straight internal strut assembly.

Tip: Completed Internal Strut Assembly. Make sure all parts connect as shown.

Hot Rod completed internal strut assembly inside the car body
Completed Internal Strut Assembly: Make sure all parts connect as shown.
Hot Rod rear, center and front strut assemblies with arrows toward the center
A: Rear, Center, and Front Strut Assemblies.

Step 2: Insert the completed strut assembly

Open Velcro straps and insert completed Strut Assembly into bottom of Hot Rod Body Sleeve as shown. Reclose Velcro straps. (diagram B)

The completed Strut Assembly moves upward into the bottom of the Hot Rod Body Sleeve. Reclose the Velcro straps around the strut assembly at the positions shown on the body sleeve.

Hot Rod completed strut assembly inserted into the bottom of the body sleeve
B: Completed Strut Assembly into Hot Rod Body Sleeve.

Step 3: Install the rear spinner axle

Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of Hot Rod Body. Tighten the knob on the "T" Joint to hold the Axles to the Struts. (diagram C)

First, slide Spinner Axle onto Strut Assembly. Second, tighten the knob on the "T" Joint.

Hot Rod Spinner Axle and T Joint sliding onto the rear strut assembly
C: Spinner Axle slides onto Strut Assembly; tighten knob on "T" Joint.

Step 4: Add two spinner wheels

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of Hot Rod should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)

Put one Spinner Wheel on each end of the Spinner Axle. The Axle Cap goes on the outside end of the axle after the wheel spin directions match the arrows shown.

Hot Rod Spinner Wheels on one axle with Axle Cap and opposite spin directions
D: Spinner Wheels and Axle Cap on Spinner Axle.

Step 5: Assemble the front spinner

Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble the front Spinner.

Use the second Spinner Axle with the two remaining Spinner Wheels. This creates the front Spinner to match the rear Spinner you assembled in Step 4.

Step 6: Mount the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Hot Rod Spinner into ferrule on top of Support Pole. (diagram E)

The Support Pole goes into the Ground Stake with the ferrule at the top. The completed Hot Rod Spinner lowers onto the ferrule from above.

Tip: Spinner Wheels on same side of Hot Rod should spin in same direction after assembly.

Hot Rod Spinner mounted onto support pole with ferrule and ground stake
E: Support Pole, ferrule, and Ground Stake.

Care

Please note: Although your Hot Rod Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Hot Rod Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.