This guide covers assembly and flying setup for the Premier Kachina Kite. It includes the vertical rod sleeves, horizontal shaping rod, Fuzzi Tail attachment options, bridle, line, and wind conditions.

Applies to: Premier Kachina Kite. See the 1 products this guide covers.

Kachina kite specs

Model Size Wind range Recommended line Frame Fabric
Kachina Kite 48 x 72 in. / 122 x 173 cm. 5 ~ 18 mph 150 lb. test; not included Carbon & Fiberglass Ripstop Polyester

Assembly instructions

Step 1: Unroll the kite

Unroll kite and lay out flat facedown (keel-side down).

Step 2: Connect the vertical rod segments

Connect pre-inserted Rod Segments inside three vertical Sleeves. Tightly pull up Velcro Tabs at bottom ends of Sleeves and close to secure Rods in Sleeves. (diagram A)

There are three vertical sleeves to secure. The Velcro tabs are at the bottom ends of the sleeves; pull them upward before closing them.

Kachina diagram showing vertical sleeves, Velcro tabs, and horizontal shaping rod
A: Rod segments, sleeves, Velcro tabs, and horizontal shaping rod.

Step 3: Insert the horizontal shaping rod

Connect two parts of Horizontal Shaping Rod. Insert ends of completed Horizontal Shaping Rod into Edge Pockets on sides of kite body. (diagram A)

The completed Horizontal Shaping Rod runs across the kite body. Each end goes outward into an Edge Pocket on the side of the kite body.

Step 4: Attach the Fuzzi Tail

Included Fuzzi Tail can be attached by tying loops on ends of Fuzzi Tail to Loops sewn onto ends of Velcro Tabs on Sleeves on both sides of kite body. Fuzzi Tail can also be attached to center Sleeve by opening Velcro Tab and reclosing with Fuzzi Tail loop inside. The Fuzzi Tail can be attached in different ways depending on amount of drag desired as shown in diagram B.

The three shown tail arrangements are least drag, medium drag, and most drag. For most drag, attach the Fuzzi Tail at the sides and at the center sleeve.

Kachina Fuzzi Tail positions for least, medium, and most drag
B: Fuzzi Tail positions for least, medium, and most drag.

Step 5: Attach the line

Make sure that Bridle is pulled completely through front of Sail, attach Line to Bridle, and your Kachina is now ready to fly!

Check the front of the Sail before attaching the Line. The Bridle should be pulled completely through the front of the Sail.

Flight instructions

Step 1: Tie on the flying line

Tie flying line to Tow Loop.

Step 2: Position the kite for launch

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Your friend should be about 75 ft. downwind from you, holding the kite with the Leading Edge pointed towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out more line

Slowly let out more line as the kite flies upward.

Flying line and wind conditions

Beaufort condition Wind [M.P.H.] Description
Calm 0 smoke rises vertically
Light air 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
Light breeze 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
Gentle breeze 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
Moderate breeze 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
Fresh breeze 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
Strong breeze 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle
Kachina wind chart with Beaufort scale and range from 5 to 18 mph
Optimum wind conditions for Kachina.

Recommended line: 150 lb. test line. Optimum wind conditions for Kachina: 5 ~ 18 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Kachina Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.