This guide covers assembly and flight setup for the Premier Mega Wild Thing Kite. It follows the manufacturer's steps for organizing the struts, installing the spine and spreaders, and launching the kite.

Applies to: Mega Wild Thing Kite. See the 1 products this guide covers.

Mega Wild Thing Kite specs

Product Size Wind range Line Frame
Mega Wild Thing Kite 127 in. x 44 ft. / 323 x 1341 cm. 7 ~ 18 mph Line not included; 250 lb. Test Line Recommended Glassforms Wrapped Fiberglass

Strut identification

Mega Wild Thing strut identification for spine, main cross spars, rear cross strut, and spreaders
Diagram A: Strut identification.
  1. Spine
  2. Main Cross Spars
  3. Rear Cross Strut
  4. Lower Body Spreaders
  5. Ear Spreaders

Assembly

Step 1: Unroll the kite

Unroll the kite.

Step 2: Identify and organize struts

Identify and organize struts. (Diagram A.)

The labeled struts are the Spine, Main Cross Spars, Rear Cross Strut, Lower Body Spreaders, and Ear Spreaders. Keep each group matched to its label before you begin assembly.

Step 3: Assemble the spine

Assemble the Spine. (Diagram B) Slide the assembled Spine into the Spine Pockets. (Diagram C) Make sure the dihedral is pointing upwards as seen in the diagram.

The Spine Struts join to make the spine before it goes into the kite. The spine sits down the center of the kite, with its ends in the two Spine Pockets and the dihedral near the upper body pointing upward.

Mega Wild Thing spine pockets, dihedral, wing connectors, and main cross spars
Diagrams B-E: Spine, spine pockets, dihedral, main cross spars, wing connectors, and bridle loop.

Step 4: Insert the main cross spars

Insert the main cross spars into the dihedral located on the spine and the Wing Connectors. (Diagram D) The spars will go through the back of the bridle line. (Diagram E)

Each Main Cross Spar runs from the dihedral on the spine out to a Wing Connector. At the bridle loop, the spar sits behind the loop.

Step 5: Insert the ear spreaders

Insert the ear spreaders into the ear pockets located at the top of the ears and in the center ear pocket located just above the dihedral.

The Ear Pockets are at the two top points of the ears, and the Center Ear Pocket is just above the dihedral. The Ear Spreaders angle down from those top pockets to the center pocket.

Mega Wild Thing ear spreaders, lower body spreaders, and rear cross strut placement
Diagrams F-G: Ear spreaders, lower body spreaders, and rear cross strut.

Step 6: Insert the lower body spreaders

Insert the Lower Body Spreaders into the Lower Body Pockets located at the end of the body just above the tail. Note that one of the Lower Body Spreaders will go behind the Spine. (Diagram F)

The Lower Body Spreaders span across the lower body, with their ends going into the side pockets shown on each side. The lower spreader sits just above the tail end of the body.

Step 7: Insert the rear cross strut

Insert the Rear Cross Strut into the Rear Cross Strut Connectors located on both Main Body Spreaders.

The Rear Cross Strut sits across the upper body, between the two Rear Cross Strut Connectors. The close-up shows the end of the Rear Cross Strut going into the connector.

Tip: You will have to bend the Rear Cross Strut slightly in order to make the Rear Cross Strut fit into both connectors.

Flight instructions

Step 1: Attach the flying line

Attach flying line to Tow Loop.

Step 2: Have a friend hold the kite downwind

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Your friend holds the kite with its Leading Edge pointed towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out more line

Slowly let out more line.

Recommended line and wind

Recommended line: 250 LB TEST LINE.

Optimum wind conditions for Mega Wild Thing: 7 ~ 18 mph.

The chart marks Mega Wild Thing from 7 through 18 M.P.H.

Mega Wild Thing Beaufort wind chart with optimum range marked
Optimum wind conditions for Mega Wild Thing: 7 ~ 18 M.P.H.
Beaufort scale category M.P.H. Description
Calm 0 smoke rises vertically
Light air 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
Light breeze 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
Gentle breeze 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
Moderate breeze 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
Fresh breeze 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
Strong breeze 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle

Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Mega Wild Thing Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.