This guide covers assembly of Premier Petite Spinner garden spinners. The same five-step setup is used across the animal, bird, fairy, bug, fish and holiday designs listed here.

Applies to: Premier Petite Spinner animal, bird, fairy, bug, fish and holiday designs. See the 29 products this guide covers.

Product sizes

Design Size (W x L)
Bay Horse, Dog, Tabby Cat 19 in. x 12.75 in.
Blue Bird, Chickadee 17.25 in. x 12.75 in.
Blue Fairy, Green Fairy 15 in. x 8.5 in.
Blue Jay 18 in. x 12.75 in.
Clownfish 16 in. x 12.75 in.
Cow 20 in. x 13.5 in.
Donkey 17.75 in. x 12.75 in.
Dragon 20 in. x 12.75 in.
Dragonfly 18.5 in. x 10 in.
Flying Flamingo 22.25 in. x 12.75 in.
Fox 17 in. x 10.75 in.
Frog 24.5 in. x 12.75 in.
Ladybug 13 in. x 10 in.
Maryland Horse, Pinto Horse 19 in. x 13.5 in.
Moose 12.75 in. x 12.25 in.
Oriole 19.25 in. x 12.75 in.
Parrot 17 in. x 12.75 in.
Party Macaw 9 in. x 15.5 in.
Peacock 15 in. x 12.75 in.
Pelican 21.5 in. x 12.75 in.
Snowy Owl 18 in. x 6 in.
Stork Boy 22.5 in. x 7.5 in.
Tiger 23 in. x 8 in.
Witch 17 in. x 13 in.

Assembly

Step 1: Remove the cotter pin and washer

Remove Cotter Pin and slide one Nylon Washer from the Spinner Axle.

The Cotter Pin is at the Body Ferrule end of the Spinner Axle. Keep the Cotter Pin and the removed Nylon Washer nearby for the next steps.

Petite Spinner axle with nylon washers, cotter pin, hub and body ferrule
A: Spinner axle, nylon washers, hub, cotter pin and body ferrule.

Step 2: Slide on the spinner wings

Slide Spinner Wings onto the Spinner Axle and replace the Nylon Washer.

Slide the Spinner Wings onto the Spinner Axle at the Hub. Put the Nylon Washer back on the axle before installing the rear body section.

Step 3: Install the rear body section

Install the Rear Body Section and slide the Cotter Pin through the hole in the Body Ferrule and bend the ends outward to secure in place.

The Body Ferrule sits on the rear body section behind the spinner wings. When secured, the Cotter Pin passes through the hole in the Body Ferrule with its ends bent outward.

Step 4: Lock the upper support pole into the hub

Slide the narrow tip of Upper Support Pole into Hub. Push the Support Pole firmly down until it locks into place and cannot be removed. This is best done with the base of the Upper Support Pole on a hard surface and using a mallet or block of wood to tap into place.

The narrow tip of the Upper Support Pole goes into the Hub below the spinner body. Push the pole down into the Hub.

Petite Spinner support poles, ferrule and ground installation
B: Upper and lower support poles, ferrule and ground installation.

Step 5: Connect the lower support pole and install

Connect Upper Support Pole with Lower Support Pole and insert into the ground.

The Lower Support Pole connects at the Ferrule below the Upper Support Pole. Insert the lower end into the ground so the spinner stands upright.

Care and mounting notes

Storms and harsh weather

For the manuals that include this note: It is recommended that you take your Petite Spinner inside during storms and harsh weather to preserve its durability.

Deck mount compatibility

For the manuals listed below: Compatible with Premier’s 6 mm Deck Mount (sold separately).

You will see this note in the Blue Fairy, Green Fairy, Tiger, Maryland Horse, Moose, Witch, Dragonfly, Cow, Fox, Flying Flamingo, Pelican, Donkey, Snowy Owl, Oriole, Peacock, Frog, Stork Boy and Blue Bird manuals.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.