This guide covers setup and flying instructions for Premier frameless ram-air sport kites in the Speedfoil RM and Barracuda series. It includes line attachment, launch, solo launch, control, landing and safety notes.

Applies to: Speedfoil RM6, Speedfoil RM8 and Barracuda 1.7 kites. See the 5 products this guide covers.

Kite specifications

Model Size Wind range Line Frame
Speedfoil RM6 - Flames, Patriotic 69 x 24.5 in. / 175 x 70 cm. 7 ~ 25 mph Included Frameless
Speedfoil RM8 - Alert, Flames 97 x 24.5 in. / 246 x 70 cm. 6 ~ 25 mph Included Frameless
Barracuda 1.7 - Tie Dye 65 x 28 in. / 161 x 71 cm. 6 ~ 20 mph Includes 80 ft. 200 lb. Test Sport Line Frameless

Terminology

Speedfoil and Barracuda terminology with leading edge, cell, bridle, tow loop and trailing edge
Speed Foil Terminology
  1. Leading Edge
  2. Cell
  3. Bridle
  4. Tow Loop
  5. Tow Loop Storage Hook-Up
  6. Trailing Edge
  7. Bridle

Preflight setup

Step 1: Check that there are no spars to assemble

Your Speed Foil derives its shape completely by “Ram-Air” effect and has absolutely no sticks or spars to assemble. Your kite is ready to fly once you have connected your two flying lines to the kite’s two tow loops.

The labeled tow loops sit at the ends of the bridle groups. The kite’s leading edge, cells, trailing edge, bridles and tow loop storage hook-up are identified in the terminology figure.

Tip: Barracuda: use the same instruction, with “BARRACUDA” in place of “Speed Foil.”

Step 2: Remove the tow loops from the storage hook-up

To reduce bridle tangling during storage, your Speed Foil includes a special storage tow loop hook-up located on the trailing edge. Please note you must remove tow loops from storage hook-up before flying. After flying, attach the tow loops back on the hook-up using a larks head knot to prevent bridles from tangling.

The storage hook-up is on the trailing edge, separate from the tow loops used for flying. Before launch, the two flying tow loops need to be free so the flying lines attach to them.

Tip: Use the same storage note for the Barracuda.

Step 3: Attach the flying lines to the tow loops

Use a larks head slip knot to attach your lines to the Tow Loop. Tightly cinch larks head slip knot and pull to the end of the Tow Loop.

The flying line forms the larks head knot around the tow loop, with the bridle leading from the tow loop to the kite. Repeat the attachment for both flying lines and both tow loops.

Speedfoil and Barracuda larks head knot attaching the flying line to the tow loop
Flying Line Attachment to Bridle

Think safety

Be sure to avoid flying near cars, people, power lines, and airports. Stunt kites can move at high speeds and are capable of inflicting damage on people and property. Both the kite and flying lines represent potential hazards. The kite and/or line can hit or cut with high force while moving at high speeds. Use your stunt kite with extreme care. Flying safely is your sole responsibility - FLY SAFE!

Beaufort wind scale

Beaufort scale Description Wind [M.P.H.]
Calm smoke rises vertically 0
Light Air Direction of wind shown by smoke, but not by wind vanes 1, 2, 3
Light Breeze Wind felt on face, leaves rustle, ordinary vane moves 4, 5, 6, 7
Gentle Breeze Leaves and small twigs in constant motion; wind extends light flag 8, 9, 10, 11, 12
Moderate Breeze Raises dust and loose paper; small branches move 13, 14, 15, 16, 17, 18
Fresh Breeze Small trees & leaves begin to sway; crested wavelets form on inland water 19, 20, 21, 22, 23, 24
Strong Breeze Large branches in motion; utility wire whistle; windows rattle 25, 26, 27, 28, 29, 30

Note: Wind conditions aloft may vary considerably from those found near ground level.

Launch

Step 1: Set equal-length lines

Lines must be out and adjusted to equal length before launching! Make sure the person holding the kite is behind it and pointing the leading edge skyward. Keep your hands forward and parallel just before launch.

Make sure the person holding the kite is behind it and pointing the leading edge skyward. Keep your hands forward and parallel just before launch.

Tip: Barracuda: Step 1 reads, “Adjust lines to equal length before launching!”

Speedfoil and Barracuda launch step 1 with equal lines and helper holding the kite
Launch Step 1

Step 2: Launch with the wind at your back

Wind must be at flyer’s back! To take off, tell your friend to release the kite. Pull both lines back with equal tension to launch the kite. Immediately return hands forward.

Stand with your back to the wind before you ask for the release. Pull both lines evenly to start the launch, then move your hands forward right away as the kite climbs.

Speedfoil and Barracuda launch step 2 with wind at the flyer’s back and kite released
Launch Step 2

Solo launching

Solo launch

With first flights it is easiest to have a helper toss the kite into the air (see Launch). When solo launching, lay the kite flat on the ground with the bridles facing up and the leading edge facing away from the flying lines. Make sure the kite is directly downwind of the flying lines. Place sand or a non-sharp object on the trailing edge to slightly weigh the kite down. Return to the flying straps and get into launch position (see Step 1). To solo launch, slowly pull the lines so that the unweighted leading edge stands off the ground. As the openings in the leading edge inflate with wind, gently pull the lines more to fully inflate the Speed Foil. Once inflated, vigorously pull both lines to get the kite airborne and tracking.

The trailing edge is the side that gets lightly weighted for a solo launch. The leading edge is left unweighted so it can stand off the ground and inflate as you pull the lines.

Tip: Barracuda: this instruction is the same, except it says “fully inflate the Barracuda.”

Maneuvering in the wind window

The wind window is an area of the sky where stunt kites maneuver. The window is shaped like a half dome. The size of the window changes with the wind speed. Higher winds produce larger windows.

The wind window sits in front of you while the wind is at your back. The center area is labeled Power Zone, and the outer curve is labeled Edge.

Speedfoil and Barracuda wind window with Power Zone, Edge and wind direction
Maneuvering in the Wind Window

Your kite will react differently in various parts of the window. The Power Zone is where your kite will pull the most and have the most speed. This is where you will have the most success launching your kite.

On the Edge, the kite is angled away from the direct wind. This lowers the speed and pull of the kite and makes landing easier. The extreme edge is the point where the kite can penetrate no further. In lighter winds, your kite becomes a victim of gravity and sinks to the ground. In higher winds your kite can hover on the edge and retain its position in the sky.

Power Zone and Edge

  • Power Zone: Most Speed; Most Pull; Fastest Control Response; Easiest Area to Launch.
  • Edge: Slower Speed; Less Pull; Slower Control Response; Easiest Area to Land.

Control

On your first launch, keep your hands next to each other and let your kite ascend as high as possible. If your kite wanders to one side, make corrections by pulling on the opposite control handle. A stunt kite turns towards the same direction it is pulled: Pull right - the kite turns right, pull left - the kite turns left. As a beginner, concentrate on steering toward the sky and maintaining plenty of altitude before doing complex stunts.

The control drawings show three handle positions: left pull, even handles and right pull. With the handles even, the kite flies straight in the same direction it is pointing.

Speedfoil and Barracuda control handle positions for left turn, straight flight and right turn
Control

The most common problem a beginner has is over controlling his or her kite. Only a few inches of pull is needed for maneuvering.

If you continue to pull to one side, your kite will make a loop. The further you pull back the line, the tighter the loop will be. At any point in a loop or a turn, you can even out your handles and the kite will move in the direction the leading edge is pointing.

After doing loops, your control lines will be twisted. This may seem troublesome but don’t worry, you will still have full control of your kite. To untwist, simply fly loops in the opposite direction.

Pull Left: Kite Turns Left. Handles Even: Kite flies straight in the same direction it is pointing. Pull Right: Kite Turns Right.

Landing

Land at the edge of the window

You’ll soon notice that as the kite flies to the edge of the window, it slows down and eventually stalls. Maneuver the kite to the outermost edge about a foot off the ground and sprint toward the kite while throwing your arms forward. Your lines will go slack and the kite will gently land.

The Edge is the lower-speed part of the wind window. Bringing the kite to the outermost edge and moving toward it makes the lines go slack for landing.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.