This guide covers assembly and basic flying instructions for the Premier Swabian Roller Kite. This guide follows the manufacturer's manual for the kite's struts, lower spine, tensioning strings, bridle and tail tow line.

Applies to: Swabian Roller Kite. See the 1 products this guide covers.

Swabian Roller Kite specs

Size Wind range Recommended line Frame
78 x 89.5 in. / 198 x 227 cm. 5 ~ 15 mph 150 lb. Test Line Recommended Sky Shark Wrapped Carbon

Assembly

Step 1: Identify the struts

Identify and organize struts. (diagram A).

Diagram A groups the Horizontal Cross Struts into upper and lower pairs, and shows the Lower Spine separately. Keep the upper pair, lower pair and Lower Spine sorted before you begin putting the frame into the kite.

Swabian Roller upper and lower Horizontal Cross Struts and Lower Spine layout
A: Horizontal Cross Struts and Lower Spine.

Step 2: Unroll the kite

Unroll the Swabian Roller kite keeping the Bridle Lines in front of (under) the kite.

As you open the kite, keep the Bridle Lines on the front, or under, side of the kite. Leave them free so they can be straightened before the flying line is attached.

Step 3: Insert the upper horizontal cross struts

Take one of the Upper Horizontal Cross Struts and slide it into one of the Upper Horizontal Cross Strut sleeves on the back of the kite making sure that the Arrow Nock remains toward the outside of the kite. Repeat with second Upper Horizontal Cross Strut on the other side of the kite. (diagram B).

Each Upper Horizontal Cross Strut slides through an Upper Horizontal Cross Strut Sleeve. The inner end connects into the factory installed dihedral, while the Arrow Nock stays at the outside edge of the kite.

Swabian Roller cross strut sleeves, dihedrals, Lower Spine and Velcro tab
B and C: Cross struts, dihedrals, Lower Spine and Velcro tab.

Step 4: Insert the lower horizontal cross struts

Repeat Step 3 with the Lower Horizontal Cross Struts and the Lower Horizontal Cross Strut Sleeves. (diagram B).

Use the Lower Horizontal Cross Strut Sleeves for the lower pair of cross struts. As with the upper pair, the inner ends connect into the factory installed dihedral and the Arrow Nocks remain at the outside of the kite.

Step 5: Install the lower spine

Slide Lower Spine into Sleeve at the base of the kite and connect the open end to the factory inserted Upper Spine section. Tightly fasten the Velcro closure over the end of the Lower Spine. (diagrams B & C).

The Lower Spine slides through the sleeve at the base of the kite and connects to the internal ferrule of the Upper Spine Section. When it is seated as shown, fasten the Velcro Tab over the Lower Spine section.

Tip: Adjustable Sail Tensioning Lines. These factory installed Tensioning Lines can be adjusted for different flying performance. If Tensioning Lines come untied, retie as shown.

Step 6: Tension the cross struts

Take one of the beaded tensioning string at the outer end of the Upper Cross Strut Sleeve and position the string into the Arrow Nock of the Upper Horizontal Cross Strut between any of the beads. Repeat with the remaining three tensioning strings. Both ends of the Upper Horizontal Cross Strut should be tensioned the same. Both ends of the Lower Horizontal Cross Strut should be tensioned the same. (diagram D).

Each beaded tensioning string sits in the Arrow Nock at the outer end of a cross strut. Match the bead position from side to side on the upper cross struts, and match the bead position from side to side on the lower cross struts.

Swabian Roller beaded tensioning string seated in the Arrow Nock
D: Beaded tensioning string in the Arrow Nock.

Step 7: Attach the tail tow line

Attach the Swivel Clip at the end of the Tail Tow Line to the Tail Loop Tab at the base of the Velcro Closure at the bottom of the kite. (diagram E).

The Tail Tow Line ends in the Swivel Clip. The Tail Loop Tab is at the bottom of the kite at the base of the Velcro Closure, and the clip attaches there as shown.

Swabian Roller Tail Tow Line Swivel Clip attaching to the Tail Loop Tab
E: Swivel Clip attached to the Tail Loop Tab.

Step 8: Unravel the daisy chain

For storage purposes the Bridle of the kite is wound into a Daisy Chain. Before attaching the flying line to the Tow Point on the Bridle, pull the Tow Point to unravel the Daisy Chain. All Bridle Lines should be straight and untangled before attaching the flying line. (diagram F).

The Tow Loop is at the end of the Daisy Chain on the Bridle Lines. After you pull it to unravel the chain, check that all Bridle Lines run straight and are not tangled before tying on the flying line.

Swabian Roller Bridle Lines, Daisy Chain and Tow Loop before flying line attachment
F: Bridle Lines, Daisy Chain and Tow Loop.

Flight instructions

Step 1: Tie on the flying line

Tie flying line to Tow Loop.

Use the Tow Loop after the Daisy Chain has been unraveled and the Bridle Lines are straight and untangled.

Step 2: Position your helper

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Your friend should be downwind from you, holding the kite so its Leading Edge points towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out more line

Slowly let out more line as the kite flies upward.

Recommended line

Recommended line: 150 lb. test line.

Optimum wind conditions

Swabian Roller wind range shown on a Beaufort Scale chart
Beaufort Scale: optimum wind conditions for Swabian Roller.

Best wind for Swabian Roller kites: 5 ~ 15 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Swabian Roller Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.