This guide covers assembly and basic flying for Premier Swept Wing Genki kites. It applies to the Genki Kite and the Blue Op-Art, Cool Orbit, Orange Op-Art, and Warm Orbit designs.
Applies to: Genki Kite; Blue Op-Art, Cool Orbit, Orange Op-Art, and Warm Orbit Genki Kites. See the 5 products this guide covers.
Specs
| Model | Size (W x L) | Wind range | Line | Frame |
|---|---|---|---|---|
| Genki Kite | 38 x 114 in. / 97 x 290 cm. | 5 ~ 20 mph | Not Included | Carbon & Fiberglass |
| Blue Op-Art, Cool Orbit, Orange Op-Art, Warm Orbit | 156 x 56 in. / 142 x 396 cm. | 4 ~ 18 mph | 150 lb. Test Line Recommended | Sky Shark Wrapped Carbon |
Assembly
Step 1: Unfold the kite
Unfold the kite and lay it facedown on the ground. Set aside all struts. The Spreader and Lower Shaping Struts parts will be grouped for you.
Keep the grouped Spreader parts separate from the grouped Lower Shaping Struts. The kite is worked on facedown before the Spreader and shaping struts are installed.
Step 2: Install the Spreader
Assemble the Spreader and slide it through the Pocket Sleeves at the Wing tips. Make sure the Spine struts remain closest to the kite sail. Securely fasten the Velcro tabs. Tie the Webbing strips at the Spines around the Spreader with a simple bow.
The Spreader runs across the kite between the wing tips. At the Spines, the webbing strips wrap around the Spine and Spreader, and the Velcro tabs close at the wing-tip pocket sleeves.

Step 3: Install the Lower Shaping Struts
Assemble one of the Lower Shaping Struts and slide it through the Lower Pocket Sleeve and into the Strut Pocket near the Spine. Repeat with the remaining Lower Shaping Strut. Securely fasten the Velcro tabs.
Each Lower Shaping Strut goes through the lower sleeve on a Velcro pocket and into the pocket near the Spine on that side. Install the second Lower Shaping Strut the same way before fastening the Velcro tabs.
Step 4: Bow the Horizontal Spreader
Bow Horizontal Spreader by sliding Line Tensioner on the Tensioning Bow Line to create approximately an 11 inch bow at center.
The Tensioning Bow Line runs above the Horizontal Spreader in the side view. Slide the Line Tensioner until the center of the Spreader has the approximately 11 inch bow shown.

Flying
To Fly: Launch the kite
Tie flying line to tow loop on the front of the kite. Have a friend stand about 75 ft. downwind from you and hold the kite with its Nose pointed towards the sky. As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls. Slowly let out more line as the kite flies upward.
Have a friend stand about 75 ft. downwind from you. The kite’s Nose points toward the sky before release, and you bring in the line with long steady pulls as it lifts.
Wind and line
| Beaufort scale | Wind (M.P.H.) | Description |
|---|---|---|
| Calm | 0 | Smoke rises vertically |
| Light Air | 1, 2, 3 | Direction of wind shown by smoke, but not by wind vanes |
| Light Breeze | 4, 5, 6, 7 | Wind felt on face; leaves rustle, ordinary vane moved by wind |
| Gentle Breeze | 8, 9, 10, 11, 12 | Leaves and small twigs in constant motion; wind extends light flag |
| Moderate Breeze | 13, 14, 15, 16, 17, 18 | Raises dust and loose paper; small branches move |
| Fresh Breeze | 19, 20, 21, 22, 23, 24 | Small trees in leaves begin to sway; crested wavelets form on inland waters |
| Strong Breeze | 25, 26, 27, 28, 29, 30 | Large branches in motion; whistling heard in telegraph wires; umbrellas used with difficulty |

The chart marks Swept Wing Genki across the 4 through 18 M.P.H. portion of the scale. Recommended line: 150 lb test line. Note: Wind conditions aloft may vary considerably from those found near ground level.
Products this guide covers
Genki Kite
Genki Kite - Blue Op-Art
Genki Kite - Cool Orbit
Genki Kite - Orange Op-Art
Genki Kite - Warm Orbit


Share:
Swept Wing Double Box Delta Assembly Instructions
Swimming Fish Assembly Instructions