This guide covers assembly and flight setup for the Premier 11 ft. Flapping Bat Kite. Follow the steps for the shaping rods, spreader rods, line attachment, and launch.

Applies to: 11 ft. Flapping Bat Kite. See the 1 products this guide covers.

Kite specs

Model Size Wind range Fabric Frame Line included
11 ft. Flapping Bat Kite 136 x 47 in. / 345 x 119 cm. 5 ~ 18 mph Ripstop Polyester Carbon & Fiberglass Not Included

Assembly

Step 1: Unroll the kite

Unroll kite and lay out flat facedown.

Arrange the kite so the head is at the top and the Spine Rod runs down the center, as shown for the rod steps.

Step 2: Install the shorter Shaping Rod

Slide the shorter of the two Shaping Rods under Spine Rod and insert into pocket on side of head about 3". Bend Shaping Rod and insert into pocket on other side of head about 3". Feed both ends into pockets evenly until Shaping Rod snaps into place. (diagram A)

The head pockets are on either side of the head. Keep the shorter Shaping Rod under the Spine Rod as you feed the two ends into the pockets evenly.

Flapping Bat shaping rods routed under the spine rod into head and lower pockets
Diagram A: Shorter and longer Shaping Rods in the head and lower pockets.

Step 3: Install the longer Shaping Rod

Repeat step 2 using longer Shaping Rod and pockets at bottom of kite. (diagram A)

The lower pockets are at the bottom edge of the kite, one on each side of the Spine Rod. The longer Shaping Rod forms the lower curve between those pockets.

Step 4: Assemble the Spreader Rods

Assemble the two Spreader Rods by inserting long, thinner rod into shorter wrapped carbon rod. (Note: the wrapped carbon rod contains an internal ferrule on one end. The thinner rod will only fit into the non-ferruled end.) (diagram B)

For each Spreader Rod, the thinner rod goes into the end of the wrapped carbon rod labeled non-ferruled end. The arrow shows the thinner rod sliding toward the wrapped carbon rod.

Flapping Bat thinner rod aligned with the non-ferruled end of the wrapped carbon rod
Diagram B: Assemble each Spreader Rod at the non-ferruled end.

Step 5: Slide the Spreader Rods into the wings

Slide Spreader Rods through sleeves on wings and into outer pockets. (diagram C)

Each Spreader Rod runs outward through a wing sleeve to an outer pocket near the wing tip. The arrows point out toward the outer pockets.

Flapping Bat spreader rods through wing sleeves into outer pockets and the dihedral
Diagram C: Spreader Rods through the sleeves and into the Dihedral.

Step 6: Seat the Spreader Rods in the Dihedral

Insert both Spreader Rods into Dihedral on Spine Rod. (diagram C)

After the outer ends are in the pockets, the inner ends of both Spreader Rods meet at the Dihedral on the Spine Rod. The arrows point inward toward the Dihedral.

Step 7: Attach the line

Attach line to bridle, and your Flapping Bat is now ready to fly!

The flight instructions call the line attachment point the Tow Loop.

Flight instructions

Launch step 1: Tie the flying line

Tie flying line to Tow Loop.

The assembly step refers to attaching the line to the bridle.

Launch step 2: Position the helper

Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.

Your friend should be about 75 ft. downwind from you with the kite head pointed towards the sky.

Launch step 3: Release and pull in line

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Launch step 4: Let out more line

Slowly let out more line as the kite flies upward.

Line and wind

  • Recommended line: Recommended line: 80 LB TEST LINE. Line is Not Included for this kite.
  • Optimum wind conditions: Optimum wind conditions for 11ft. Flapping Bat. Best wind for 11ft. Flapping Bat: 5 ~ 18 mph.
Flapping Bat Beaufort wind chart marking the 11ft. Flapping Bat range
Beaufort scale: Optimum wind conditions for 11ft. Flapping Bat.

Products this guide covers

Download the original manual

11 ft. Flapping Bat Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.