This guide covers assembly and flying setup for the Premier 13 ft. Skeleton Kite. It follows the manufacturer's steps for the head struts, body connection, hip struts and launch.
Applies to: 13 ft. Skeleton Kite. See the 1 products this guide covers.
Kite specs
| Model | Size (W x L) | Wind range | Line | Frame | Fabric |
|---|---|---|---|---|---|
| 13 ft. Skeleton Kite | 13 ft. x 35 in. | 6 ~ 14 mph | Includes 300 ft. of 30 lb. test on D handle | Fiberglass | Ripstop Polyester |
Assembly
Step 1: Locate the head struts
Remove the kite from the bag and locate the Head Struts. (diagram A)
You are looking for the Lower Head Strut, the Horizontal Head Strut, and the Main Head Cross Struts. The Main Head Cross Struts are the two matching struts shown together.

Step 2: Insert the main cross struts
Insert one Main Cross Strut into Head Pockets A and B. Insert the second Main Cross Strut into Head Pockets C and D. (diagram B)
The two Main Head Cross Struts run diagonally across the head and meet at the center webbing. Their ends go into the labeled head pockets: A to B for one strut, and C to D for the other.

Step 3: Insert the horizontal head strut
Insert the Horizontal Head Strut into Head Pockets E and F. (diagram B)
The Horizontal Head Strut runs straight across the head through the center area. Its ends seat in Head Pocket E on one side and Head Pocket F on the other.
Step 4: Insert the lower head strut
Insert the Lower Head Strut into the Head Pockets G and H. (diagram B)
The Lower Head Strut fits across the lower part of the head. Its ends go into Head Pocket G and Head Pocket H.
Step 5: Tie the struts at the center
Tie the Spine, Cross Struts, and Horizontal Cross Strut together with the Center Webbing. Use a simple bow knot like tying your shoe. (diagram B)
The Center Webbing is at the point where the Main Head Cross Struts, Horizontal Head Strut, and Spine Strut meet. Tie the webbing at that center point so the struts are held together there.
Step 6: Attach the neck Velcro to the head Velcro
Line the center of the Neck Velcro with the center of the Head Velcro and attach Velcro together. Spine Strut should be as centered on Neck Velcro as possible. (diagram D)
The Head Velcro is on the lower edge of the head, and the Neck Velcro is at the top center of the body. Bring the two Velcro patches together with the Spine Strut centered over the Neck Velcro.

Step 7: Attach the head clips
Attach Head Clips to Body Shoulder Loops. (diagram D)
There is a Head Clip on each side of the head and a Shoulder Loop at each shoulder. Use the loop beside each Shoulder Pocket; the Shoulder Strut is pre-installed through the Shoulder Sleeve.
Step 8: Set the lower hip strut
The Upper Hip Strut and the Lower Hip Strut come pre-installed in the Center Hip Sleeve. Bend the Lower Hip Strut into a curve and insert through the Lower Hip Sleeves and into the Lower Hip Pockets. (diagram E)
The Center Hip Sleeve is at the middle of the hips. The Lower Hip Strut curves downward from that sleeve, passes through both Lower Hip Sleeves, and its ends sit in the Lower Hip Pockets.

Assembly note
Your Skeleton Kite is designed so that the head can be easily disconnected from the body. This feature allows for easier assembly, disassembly, and storage.
Flying
Step 1: Attach the flying line
Attach flying line to tow loop. (diagram F)
The Tow Loop is at the bridle point in front of the kite. Attach the flying line to that loop, not directly to the bridle lines.

Step 2: Launch the kite
Have a friend stand about 75 feet downwind from you and hold the kite with its nose pointed towards the sky. As the wind catches the kite, signal your friend to release it while you steadily pull in line until the kite is aloft. As the kite flies upward, slowly release more line.
Stand with your back to the wind while your friend holds the kite downwind. Keep the nose pointed toward the sky until the wind catches the kite.
Fabric note
Please note all un-hemmed edges of your Skeleton kite's fabric are hot-cut to prevent fraying; however, some fraying will occur under ordinary use. This is normal and will not affect the performance of the kite.
Wind conditions
| Beaufort scale | Wind [M.P.H.] |
|---|---|
| Calm | 0 |
| Light Air | 1, 2, 3 |
| Light Breeze | 4, 5, 6, 7 |
| Gentle Breeze | 8, 9, 10, 11, 12 |
| Moderate Breeze | 13, 14, 15, 16, 17, 18 |
| Fresh Breeze | 19, 20, 21, 22, 23, 24 |
| Strong Breeze | 25, 26, 27, 28, 29, 30 |

Optimum wind conditions for 13 ft Skeleton Kite: 6-14 M.P.H. Note: Wind conditions aloft may vary considerably from those found near ground level.


13 ft. Skeleton Kite
Share:
13 ft. Flo-Tail Delta Kite Assembly Instructions
14 ft. Delta Kite Assembly Instructions