This guide covers assembling and flying the Premier 19 ft. Delta kite. It applies to the Patriotic design in this size.

Applies to: 19 ft. Delta Kite - Patriotic. See the 1 products this guide covers.

Specifications

Model Size (W x L) Wind range Fabric Frame Line included
19 ft. Delta Kite - Patriotic 228 x 112 in. / 572 x 285 cm. 5 ~ 20 mph Ripstop Polyester Glassforms Wrapped Fiberglass Not Included

These huge kites develop tremendous pull and should only be handled by a responsible adult.

Assembly

Step 1: Unroll the kite

Unroll kite and lay out flat facedown.

Start with the kite opened flat so the sleeves, pockets, keel and tow point can be found for the next steps.

Step 2: Assemble the struts

Your frame consists of 11 strut pieces: 2 pieces make up the Cross Strut. 9 pieces make up the Leading Edge and Spine Assemblies (3 Middle Struts, 6 End Struts.) Assemble the Leading Edge Struts and Spine by connecting 2 end struts to each middle strut.

Join the pieces at the ferrules. Each leading edge and spine assembly is made from one middle strut with one end strut connected at each end, and the cross strut is made from its 2 pieces.

19 ft. Delta six end struts grouped together
Six End Struts.

Step 3: Insert the spine rod

Insert assembled Spine Rod into Spine Sleeve.

The spine sleeve runs up the center of the kite. Slide the assembled spine into the spine sleeve in the direction marked “slide Spine into Spine Sleeve.”

19 ft. Delta frame layout with sleeves, pockets, keel and tow point
Frame layout, pockets, keel and tow point.

Step 4: Insert the leading edge struts

Insert Leading Edge Struts into Leading Edge Sleeve Opening. Push the assembled Leading Edge Struts all the way to the Wing Tips. Tip: Some people find it easier to install a small amount of tape on the ferrules to help hold the Strut assembly together while inserting it.

Use one assembled leading edge strut on each side of the kite. The sleeve openings are near the upper center, and the arrows show each strut sliding down the leading edge sleeve toward a wing tip.

Step 5: Insert the cross strut

Insert Cross Strut into Pockets.

The assembled cross strut lies across the kite. Put each end into the pocket shown at the left and right sides.

Step 6: Attach the line

Attach Line to Tow Point, and your 19ft. Delta is now ready to fly!

The tow point is on the keel. Attach the flying line there with a Larks Head Knot.

Flight instructions

Step 1: Tie the flying line

Tie flying line to Tow Loop.

Step 2: Position your helper

Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.

Your friend should be downwind from you with the head of the kite pointed towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out line

Slowly let out more line as the kite flies upward.

Line and wind conditions

Beaufort scale Wind (M.P.H.) Description
Calm 0 Smoke rises vertically
Light air 1 2 3 Direction of wind shown by smoke, but not by wind vanes
Light breeze 4 5 6 7 Wind felt on face, leaves rustle, ordinary vane moves
Gentle breeze 8 9 10 11 12 Leaves and small twigs in constant motion; wind extends light flag
Moderate breeze 13 14 15 16 17 18 Raises dust and loose paper; small branches move
Fresh breeze 19 20 21 22 23 24 Small trees & leaves begin to sway; crested wavelets form on inland water
Strong breeze 25 26 27 28 29 30 Large branches in motion; utility wire whistle; windows rattle
19 ft. Delta Beaufort wind chart with the kite range marked
Optimum wind conditions for 19ft. Delta.

Recommended line: 500 lb test line. Optimum wind conditions for 19ft. Delta: 5 ~ 20 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

19 ft. Delta Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.