This guide covers assembly for Premier two-wheel Bike Spinners. It applies to the 20 in. character designs and the 22 in. Road Bike Man and Woman designs.
Applies to: 20 in. Bike Spinners and 22 in. Road Bike Spinners. See the 18 products this guide covers.
Have a 30 in. Bike Spinner? It goes together differently; see the 30 in. Bike Spinner Assembly Instructions.
Models and sizes
| Designs | Size (W x L) |
|---|---|
| Uncle Sam, Cow | 20 in. x 17.5 in. |
| Easter Bunny, Flamingo | 20 in. x 16.5 in. |
| Kitty | 20 in. x 16 in. |
| Ladybug, Snowman | 20 in. x 17 in. |
| Monkey, Puppy | 20 in. x 15.5 in. |
| Parrot | 23 in. x 17 in. |
| Reindeer | 20 in. x 18.5 in. |
| Santa | 20 in. x 20.5 in. |
| Scarecrow, Turtle | 20 in. x 18 in. |
| Skeleton | 20 in. x 19 in. |
| Tree Frog | 20 in. x 15 in. |
| Road Bike Man 1555, Road Bike Woman 1555 | 22 in. x 17 in. |
Assembly
Step 1: Lock the upper support pole into the hub
Slide the narrow, plastic tipped end of the Upper Support Pole into Star Lock Hub. Push down on the hub until the Upper Support Pole locks into place and cannot be removed. (Diagram A)
The plastic tip of the Support Pole goes up into the Star Lock Hub from below. Push the hub down hard onto the pole.
Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Step 2: Connect the body strut to the bike frame
Connect the Main Internal Body Strut to the Bike Frame Strut Assembly as shown in Diagram A. Attach all Velcro tabs on the inside of the Body Sleeve to the corresponding Velcro tabs on the Bike Frame.
The Main Internal Body Strut runs through the Body Sleeve, and the body sits above the Bike Frame Strut Assembly before it is joined to the frame. Match the Velcro tab inside the Body Sleeve with the Velcro tab on the Bike Frame.
Step 3: Install the axles
Slide one of the Axles onto the rear axle fitting. The axle can point either to the right or left but not to the top or bottom since this is where the wheel will sit. Place a threaded Axle Lock Nut after it and tighten. Repeat with the front axle fitting making sure the axle is pointed the same direction as the rear axle. (Diagram B)
Each axle sticks out sideways from its fitting because the wheel needs the space above and below it. Point the front axle the same way as the rear axle so both wheels end up on the same side of the bike.

Step 4: Add the wheels and axle caps
Slide one wheel onto each axle and tap the axle caps onto the ends of the axles using a mallet or a piece of wood. (Diagram C)
Slide each Spinner Wheel onto its Spinner Axle from the outside. The Axle Cap goes on the end of the axle after the wheel is in place.

Step 5: Set the spinner on the ground stake
Drive Ground Stake into ground and insert non-ferruled end of the Lower Support Pole into Ground Stake. Insert the Upper Pole Section of completed Bike Spinner into ferrule on top of Lower Support Pole. (Diagram D)
The Lower Support Pole sits in the Ground Stake with the ferrule at the top. The completed Bike Spinner’s Upper Support Pole slides down into that ferrule.

Care and weather
Please note: Although your Bicycle Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.
Products this guide covers
20 in. Bike Spinner - Easter Bunny
20 in. Bike Spinner - Flamingo
20 in. Bike Spinner - Kitty
20 in. Bike Spinner - Monkey
20 in. Bike Spinner - Puppy
20 in. Bike Spinner - Reindeer
20 in. Bike Spinner - Santa
20 in. Bike Spinner - Scarecrow
20 in. Bike Spinner - Skeleton
20 in. Bike Spinner - Turtle
20 in. Bike Spinner -Snowman
22 in. Road Bike Spinner - Man 1555
22 in. Road Bike Spinner - Woman 1555
20 In Bike Spinner - Uncle Sam
20 in. Bike Spinner - Cow
20 in. Bike Spinner - Ladybug
20 in. Bike Spinner - Parrot
20 in. Bike Spinner - Tree Frog
Download the original manuals
Premier prints a manual for each design; the steps are the same apart from the differences noted above.



Share:
19 ft. Delta Kite Assembly Instructions
20 in. Zombie WhirliGig Spinner Assembly Instructions