This guide covers assembly and flying setup for Premier 21 ft. Skeleton Kites. It applies to the standard Skeleton, Pirate Skeleton, and Day of the Dead Dia De Los Muertos Skeleton designs.

Applies to: 21 ft. Skeleton Kite designs. See the 3 products this guide covers.

Kite specs

Designs Size (W x L) Wind range Line Frame Fabric
21 ft. Skeleton Kite; 21 ft. Pirate Skeleton Kite; 21 ft. Day of the Dead Dia De Los Muertos Skeleton Kite 21 ft. x 58 in. 6 ~ 14 mph 150 lb. Test Line Recommended; Not Included Fiberglass Ripstop Polyester

Assembly

Step 1: Locate the struts

Remove the kite from the bag and locate the Head and Shoulder Struts. (diagram A)

The labeled struts are the Lower Head Strut, Upper Head Strut, Horizontal Head Strut, Main Head Cross Struts, Lower Spine Strut, and Shoulder Struts.

21 ft. Skeleton Kite struts laid out and labeled before assembly
A: Strut layout

Step 2: Insert the lower spine strut

Insert the Lower Spine Strut through the Spine Sleeve and through the Bridle Loop. Insert one end into the Ferrule. Insert the other end into Head Pocket A. (diagram B)

The Lower Spine Strut runs on the center line below the pre-installed Upper Spine Strut. Head Pocket A is at the lower end of the head, and the Ferrule is above it on the center spine.

21 ft. Skeleton Kite head with labeled struts, pockets, bridle loop, ferrule, and center webbing
B: Head strut placement

Step 3: Insert the main cross struts

Insert one Main Cross Strut into Head Pockets B and C. Insert the second Main Cross Strut into Head Pockets D and E. (diagram B)

The Main Head Cross Struts cross diagonally through the center of the head. One runs from Head Pocket B to Head Pocket C, and the other runs from Head Pocket D to Head Pocket E.

Step 4: Insert the horizontal head strut

Insert the Horizontal Head Strut into Head Pockets F and G. (diagram B)

This strut runs straight across the head through the center webbing area. Head Pocket F is on one side of the head and Head Pocket G is on the opposite side.

Step 5: Insert the upper head strut

Insert the Upper Head Strut through the Upper Head Strut Sleeve and into the Head Pockets H and I. (diagram B)

The Upper Head Strut Sleeve is near the top of the center spine. The strut runs across the upper part of the head between Head Pockets H and I.

Step 6: Insert the lower head strut

Insert the Lower Head Strut into the Head Pockets J and K. (diagram B)

The Lower Head Strut runs across the lower part of the head. Head Pockets J and K are the lower side pockets shown near the bottom of the head.

Step 7: Tie the center webbing

Tie the Spine, Cross Struts, and Horizontal Cross Strut together with the Center Webbing. Use a simple bow knot like tying your shoe. (diagram B)

The Center Webbing is at the point where the spine, diagonal cross struts, and horizontal strut meet. Tie only at that center point shown on the head.

Step 8: Join the shoulder struts

Take Shoulder Struts and join at Center Ferrule. (diagram C)

Bring the two shoulder struts end to end at the Ferrule. Once joined, they form the long shoulder strut assembly used in the next step.

21 ft. Skeleton Kite shoulder struts joining at the center ferrule
C: Shoulder struts and ferrule

Step 9: Slide in the shoulder struts

Slide joined Shoulder Struts through Shoulder Sleeve and slip into Shoulder Pockets. You may need to pull back the end of the Pocket with some force to stick the Shoulder Pockets in place. (diagram D)

The Shoulder Sleeve runs across the body below the head. The joined Shoulder Struts pass through that sleeve, with the ends seated in the Shoulder Pockets at both sides.

21 ft. Skeleton Kite shoulder sleeve, shoulder pockets, Velcro, head clips, and shoulder loops
D: Shoulder and neck attachment

Step 10: Attach the head Velcro to the neck Velcro

Line the Center of the Neck Velcro with the center of the Head Velcro and attach Velcro together. Spine Strut should be as centered on Neck Velcro as possible. (diagram D)

The Head Velcro and Neck Velcro meet at the neck opening. Keep the center spine aligned with the center of the Neck Velcro when you press the pieces together.

Step 11: Attach the head clips

Attach Head Clips to Body Shoulder Loops. (diagram D)

There is a Head Clip on each side of the head area. Clip each one to the nearby Shoulder Loop on the body.

Step 12: Set the hip struts

The Upper Hip Strut and the Lower Hip Strut come pre-installed in the Center Hip Sleeve. Bend the Lower Hip Strut into a curve and insert through the Lower Hip Sleeves and into the Lower Hip Pockets. (diagram E)

The Upper Hip Strut runs from the Center Hip Sleeve toward the Upper Hip Pockets. The Lower Hip Strut curves downward through the Lower Hip Sleeves and finishes in the Lower Hip Pockets on both sides.

21 ft. Skeleton Kite hip struts with center hip sleeve, lower hip sleeves, and hip pockets
E: Hip strut placement

Head and body connection

Your Skeleton Kite is designed so that the head can be easily disconnected from the body. This feature allows for easier assembly, disassembly, and storage.

Flying

Step 1: Attach the flying line

Attach flying line to tow loop. (diagram F)

The Tow Loop is at the end of the bridle on the front of the kite. Attach the flying line at that loop.

21 ft. Skeleton Kite front with bridle and tow loop labeled
F: Tow loop on bridle

Step 2: Launch the kite

Have a friend stand about 75 feet downwind from you and hold the kite with its nose pointed towards the sky. As the wind catches the kite, signal your friend to release it while you steadily pull in line until the kite is aloft. As the kite flies upward, slowly release more line.

Stand upwind of your friend. Your friend holds the kite downwind with the nose pointed toward the sky until you signal the release.

Fabric edges

Please note all un-hemmed edges of your Skeleton kite's fabric are hot-cut to prevent fraying; however, some fraying will occur under ordinary use. This is normal and will not affect the performance of the kite.

Wind conditions

21 ft. Skeleton Kite optimum wind chart marked from 6 to 14 mph
Optimum wind conditions for 21 ft. Skeleton Kite

Optimum wind conditions for 21 ft. Skeleton Kite: 6 ~ 14 mph. Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

21 ft. Skeleton Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.