This guide covers assembly and basic flying instructions for 25 and 30 in. Diamond kites. It shows where the cross struts, plastic center molding, bridle, and tow point are used.

Applies to: Premier 25 in. and 30 in. Diamond kites. See the 28 products this guide covers.

Specs

Model Size Wind range Fabric Frame Line
25 in. Diamond 20 x 25 in. / 51 x 64 cm. 7 ~ 15 mph Ripstop Polyester Fiberglass Includes 300 ft. of 20 lb. Test Line and Winder
30 in. Diamond, 300 ft. line designs 32 x 30 in. / 81 x 76 cm. 5 ~ 15 mph Ripstop Polyester Fiberglass Includes 300 ft. of 20 lb. Test Line and Winder
30 in. Diamond, 120 ft. line designs 32 x 30 in. / 81 x 76 cm. 5 ~ 15 mph Polyester Fiberglass Includes 120 ft. 20 lb. Test Line & Winder

Assembly

Step 1: Unroll the kite

Unroll Kite.

Step 2: Identify and organize the struts

Identify and organize struts.

The kite uses two Cross Struts, one for each side.

Diamond kite cross struts shown as two long rods
A: Cross Struts.

Step 3: Insert the cross struts

Insert the Cross Struts into the Cross Strut Pockets on both sides of the kite.

Work from the back of the kite. The Cross Strut Pockets are at the left and right edges, with the Spine running down the center.

Diamond kite back with cross strut pockets, center molding, cross struts, and spine
B: Back of kite with Cross Strut Pockets, Plastic Center Molding, Cross Struts, and Spine.

Step 4: Slide the struts into the center molding

Slide the Cross Struts into the Plastic Center Molding.

The Plastic Center Molding is at the center of the kite on the Spine. The inner ends of both Cross Struts meet at this molding.

Step 5: Attach the flying line

Attach the flying line to the tow point on the bridle on the front of the kite.

Use the front of the kite. The Bridle runs to the Tow Point near the upper part of the sail.

Diamond kite front with bridle and tow point
C: Front of kite with Bridle and Tow Point.

Ready to fly

Your kite is now ready to fly!

Flight instructions

Step 1: Attach the flying line

Attach flying line to Tow Loop.

This is the same bridle attachment point labeled Tow Point on the front of the kite.

Step 2: Have a friend hold the kite

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Stand with your back to the wind so downwind is in front of you. Your friend should be about 75 ft. away in that direction.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out more line

Slowly let out more line as the kite flies upward.

Recommended line and wind conditions

M.P.H. Beaufort scale Wind
0 CALM smoke rises vertically
1, 2, 3 LIGHT AIR Direction of wind shown by smoke, but not by wind vanes
4, 5, 6, 7 LIGHT BREEZE Wind felt on face, leaves rustle, ordinary vane moves
8, 9, 10, 11, 12 GENTLE BREEZE Leaves and small twigs in constant motion; wind extends light flag
13, 14, 15, 16, 17, 18 MODERATE BREEZE Raises dust and loose paper; small branches move
19, 20, 21, 22, 23, 24 FRESH BREEZE Small trees & leaves begin to sway; crested wavelets form on inland water
25, 26, 27, 28, 29, 30 STRONG BREEZE Large branches in motion; utility wire whistle; windows rattle
Diamond kite Beaufort scale wind chart with an optimum wind band
Beaufort scale: wind conditions chart.

RECOMMENDED LINE: 20 LB TEST LINENote: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.