Use this guide to assemble Premier two-wheel Bicycle Spinners. It covers the shared bike spinner frame, axles, wheels, support pole, and the design-specific first step for each style.
Applies to: Premier 30 in. Bike Spinners and 35 in. Road Bike Spinner - Woman. See the 19 products this guide covers.
Have a 20 in. Bike Spinner? It goes together differently; see the 20 in. Bike Spinner Assembly Instructions.
Product sizes
| Designs | Size (W x L) |
|---|---|
| Bulldog, Flamingo, Puppy | 30 in. x 27 in. |
| Easter Bunny, Pig | 30 in. x 27.5 in. |
| Kitty, Pilgrim, Rat, Snowman | 30 in. x 28 in. |
| Parrot | 36.5 in. x 29 in. |
| Gnome | 30 in. x 33.5 in. |
| Reindeer | 30 in. x 32 in. |
| Santa | 30 in. x 24.5 in. |
| Scarecrow, Turtle, Uncle Sam | 30 in. x 30 in. |
| Skeleton | 30 in. x 32.5 in. |
| T-Rex | 35 in. x 30 in. |
| Road Bike Spinner - Woman | 35 in. x 28 in. |
Care note
Please note: Although your Bicycle Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.
Assembly
Step 1: Connect the strut assembly
The Strut Assembly of your bike spinner is shipped in two or three sections, depending on design. Connect the Main Internal Body Strut to the Bike Frame Strut Assembly as shown in diagram A. Attach all Velcro tabs on the inside of the Body Sleeve to the corresponding Velcro tabs on the Bike Frame.
The Body Sleeve sits above the Bike Frame Strut Assembly, with the Main Internal Body Strut running between them. Match the Velcro tabs on the inside of the Body Sleeve to the tabs on the Bike Frame before moving on.
Tip: Parrot, Santa, Pilgrim, Turtle, Rat, and Snowman are shipped in three sections: Parrot slides the Tail Support Rod into the Body Sleeve and connects it to the Internal Strut Assembly; Santa slides the Sack Support Rod into the Body Sleeve; Pilgrim, Turtle, Rat, and Snowman slide the Basket over the Bike Frame and Velcro into place first. Scarecrow slides the Pumpkin Support Rod into the Body Sleeve first, and T-Rex slides the tail strut into the fitting on the Main Internal Body Strut after connecting the main strut.

Step 2: Install the axles
Unscrew the threaded Axle Lock Nuts and slide one of the Axles onto the rear axle fitting. The axle can point either to the right or left but not to the top or bottom since this is where the wheel will sit. Replace the threaded Axle Lock Nut and tighten. Repeat with the front axle fitting making sure the axle is pointed the same direction as the rear axle. (diagram B)
Remove the Axle Lock Nut before sliding the Spinner Axle onto the Strut Assembly. Use the same right-or-left direction for both axles so the two wheels will sit on the same side of the frame.

Step 3: Add the wheels and axle caps
Slide one wheel onto each axle and tap the axle caps onto the ends of the axles using a mallet or a piece of wood. (diagram C)
Each Spinner Wheel slides onto a Spinner Axle from the outside. The Axle Cap goes on the outer end of the axle after the wheel is in place.

Step 4: Set the spinner on the support pole
Drive Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Bike Spinner into ferrule on top of Support Pole. (diagram D)
The Support Pole stands in the Ground Stake with the ferrule at the top. Lower the completed Bike Spinner so its Upper Pole Section fits into that ferrule.

Products this guide covers
30 in. Bike Spinner - Bulldog
30 in. Bike Spinner - Flamingo
30 in. Bike Spinner - Gnome
30 in. Bike Spinner - Kitty
30 in. Bike Spinner - Pig
30 in. Bike Spinner - Pilgrim
30 in. Bike Spinner - Puppy
30 in. Bike Spinner - Rat
30 in. Bike Spinner - Santa
30 in. Bike Spinner - Skeleton
30 in. Bike Spinner - Snowman
30 in. Bike Spinner - T-Rex
30 in. Bike Spinner - Turtle
35 in. Road Bike Spinner- Woman
30 in. Bike Spinner - Easter Bunny
30 in. Bike Spinner - Parrot
30 in. Bike Spinner - Reindeer
30 in. Bike Spinner - Scarecrow
30 in. Bike Spinner - Uncle Sam
Download the original manuals
Premier prints a manual for each design; the steps are the same apart from the differences noted above.



Share:
27 in. Pilot Pal Spinner Assembly Instructions
32 in. Motorcycle Spinner Assembly Instructions