This guide covers assembly and basic flying setup for Premier 38 in. Travel Diamond kites. It applies to the Orbit Tron and Tecmo Tron designs.

Applies to: 38 in. Travel Diamond Kite - Orbit Tron and Tecmo Tron. See the 2 products this guide covers.

Kite specs

Designs Size Wind range Fabric Frame Line
Orbit Tron, Tecmo Tron 38 x 38 in. / 96.5 x 96.5 cm. with 10 ft. Streamer 6 ~ 16 mph Ripstop Polyester Fiberglass SnapRod Includes Yo-Yo Winder with 300 ft. 30 lb. test line

Assembly overview

Assembly of your Travel Diamond is a snap!

All Struts on your Travel Diamond are attached to the Frame and fully Shock Corded. This eliminates loose pieces and assembly guesswork.

The struts stay connected by the shock cord, so you are bringing attached parts together rather than sorting separate rods. The ferrules are the sleeves shown between strut sections.

Assembly

Step 1: Push together the corded struts

Push together the Corded Struts. Make sure the Struts are fully seated in Ferrules. (diagram A)

Slide the strut ends together at the ferrule, with the shock cord running through the strut sections. When this step is complete, the strut sections sit fully in the ferrule.

Travel Diamond struts connected by shock cord with ferrule between the strut sections
Diagram A: Corded struts, shock cord and ferrule.

Step 2: Insert the cross struts

Insert Cross Struts into the Center Fitting. The arms on the Center Fitting should be pointing up (away from the Sail). (diagram B and diagram C)Assembled incorrectly: If the center fitting is turned so that the arms point inwards towards the sail, then the assembled kite will look like this with the sail bowing out in the same direction as the bridle. This is incorrect.Assembled correctly: If the center fitting is turned correctly so that the arms are pointing out away from the sail, then the assembled kite will look like this, with the sail bowing in the opposite direction from the bridle. This is the correct configuration.

The two Cross Struts enter the Center Fitting from opposite sides. The arms of the Center Fitting should point up and away from the Sail, so the assembled kite matches the correct view with the Sail bowing opposite the Bridle.

Travel Diamond Cross Struts inserted into the Center Fitting with arms pointing away from the Sail
Diagram B: Cross Struts and Center Fitting orientation.
Travel Diamond correct and incorrect sail bowing direction compared with the Bridle
Diagram C: Correct and incorrect assembled configuration.

Step 3: Check the tow point

Your kite's Tow Point has been set at the factory on the Factory Mark. This setting is best for most all winds. Please note adjustments can be made on your kite for different wind conditions. (diagram D)

The Tow Loop sits on the bridle, with the bridle legs labeled toward top of Kite and toward bottom of Kite. You can see the Factory Set Mark in Diagram D, plus marked positions for flying in low winds and high winds.

Travel Diamond bridle showing Factory Set Mark, Tow Loop, and low and high wind settings
Diagram D: Tow Point and wind adjustment settings.

Step 4: Remove the rubber band from the tail

Take rubber band off Tail before flying.

Flying

Step 1: Attach the flying line

Attach Flying Line to Tow Loop.

Use the Tow Loop shown on the bridle. The Tow Loop is the attachment point for the flying line.

Step 2: Launch the kite

Have a friend stand about 75 feet downwind from you and hold the Kite with its nose pointed towards the sky.As the wind catches the Kite, signal your friend to release it while you steadily pull in Line until the Kite is aloft.As the Kite flies upward, slowly release more Line.

Keep the kite nose pointed toward the sky for release, then pull in line steadily as it lifts.

Wind conditions

Travel Diamond Beaufort scale chart for wind in miles per hour
Beaufort Scale: Optimum wind conditions for 38 in. Travel Diamond Kite.

Kite wind range: 6 ~ 16 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

38 in. Travel Diamond Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.