This guide covers assembly of the 40 in. x 27 in. New Holland Tractor Spinner. Connect the struts, install the spinner wheels, and set the spinner on its support pole according to the Premier manual.

Applies to: 40 in. New Holland Tractor Spinner. See the 1 products this guide covers.

Assembly

Step 1: Connect the front and center struts

The Strut Assembly of your New Holland Tractor spinner is shipped in three sections. Connect Center Rod of the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)

The center strut assembly is the upright section with a short horizontal center rod. The front strut assembly is the longer horizontal section with two downward struts.

New Holland Tractor center strut assembly connecting to the front strut assembly
A. Center Strut Assembly connects to the Front Strut Assembly.

Step 2: Install the completed strut assembly in the body sleeve

Open Velcro seam and connect the Center Rod of the Internal Rear Strut Assembly to the Center Strut Assembly. Insert completed Strut Assembly into bottom of the New Holland Tractor Body Sleeve as shown. It is easiest to connect the Struts before sliding the Front of the Strut Assembly into place. Reclose Velcro seam. (diagram B)

The rear strut assembly is labeled as the Internal Body Struts inside the tractor body. When the completed strut assembly is in place, it runs through the bottom of the body sleeve, with the front portion slid into position after the struts are connected.

Tip: Completed Internal Strut Assembly: Make sure all parts connect as shown.

New Holland Tractor internal strut assembly with rods positioned inside the tractor body
Completed Internal Strut Assembly. Make sure all parts connect as shown.
New Holland Tractor completed strut assembly inserted into the body sleeve
B. Connect the completed Strut Assembly to the Internal Body Struts and insert it into the Tractor Body Sleeve.

Step 3: Attach a spinner axle to the rear strut

Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of New Holland Tractor Body. Tighten knob on the “T” Joint to hold the Axles to the Struts. (diagram C)

The spinner axle uses the “T” Joint at its center. Slide that joint onto the rear strut assembly at the back of the tractor body, then tighten the knob on the joint.

New Holland Tractor spinner axle sliding onto the rear strut assembly
C. Slide the Spinner Axle onto the Strut Assembly and tighten the knob on the “T” Joint.

Step 4: Add two spinner wheels to the axle

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of Tractor should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)

The two wheels for this axle sit on opposite sides of the tractor body. One end of the axle is already capped; the second Axle Cap goes onto the uncapped end after the wheels are on.

New Holland Tractor spinner wheels and axle cap on one spinner axle
D. Spinner Wheels on the same axle should spin in opposite directions.

Step 5: Assemble the front spinner

Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble the front Spinner.

Use the same wheel-direction rule from Step 4 for the front spinner. The finished assembly has the front and rear spinner wheels on the same side of the tractor spinning in the same direction.

Step 6: Set the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed New Holland Tractor Spinner into ferrule on top of Support Pole. (diagram E)

The ground stake sits below the ground line, with the support pole standing above it. The top of the support pole is the ferrule that receives the Upper Pole Section of the completed spinner.

New Holland Tractor spinner on support pole, ferrule, and ground stake
E. Insert the completed spinner into the ferrule on top of the Support Pole.

Care and storage

Although your New Holland Tractor Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

40 in. New Holland Tractor Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.