This guide covers assembly and flight setup for the Premier Dimension X kite. It follows the manufacturer’s steps for organizing the struts, tensioning the kite, installing the cross struts, and launching.

Applies to: Key Lime Dimension X Kite. See the 1 products this guide covers.

Dimension X specs

Model Size Wind range Line Frame
Key Lime Dimension X Kite 83 x 107 in. / 211 x 272 cm. 7 ~ 18 mph 250 lb. Test Line Recommended; not included Glassforms Wrapped Fiberglass

Assembly instructions

Step 1: Identify the struts

Identify and organize struts (Diagram A).

Separate the struts into the three labeled groups: Middle Cross Struts, Top Cross Struts, and Bottom Cross Struts. Each group has two struts.

Dimension X struts labeled middle, top, and bottom cross struts
Diagram A: Middle, top, and bottom cross struts.

Step 2: Unroll the kite

Unroll the kite into X-shape (Diagram B).

The sail opens into an X shape with the attached side struts running along the left and right sides. The tensioning strings are near the outside ends of the side struts.

Dimension X X-shape with side strut ferrule, arrow nock, tensioning string, and kite loop
Diagrams B-E: X-shape, side strut connection, tensioning string, and kite loop.

Step 3: Connect the left side struts

Connect the two left side struts that are already attached to the kite (Diagram C).

Use the ferrule shown on the left side strut joint. The close-up marks where to insert the strut into the ferrule.

Step 4: Set the tensioning string

Slide the beaded Tensioning String into the Arrow Nock between any of the beads for preferred tension (Diagram D). Make sure the other side of the pole is attached to the kite with the Kite Loop located by the strut (Diagram E).

The arrow nock is at the end of the side strut. The beaded tensioning string sits in the arrow nock, while the kite loop is at the opposite end of that pole near the strut.

Step 5: Repeat on the right side

Repeat Steps 3 and 4 for the right side of the kite. The kite should now look like Diagram F.

Both side struts should now be connected and tensioned. The two side strut assemblies stand along the left and right sides of the X-shaped kite (Diagram F).

Dimension X with both side struts connected along the left and right sides
Diagram F: Side struts connected on both sides.

Step 6: Insert the left middle cross strut

Insert a Middle Cross Strut into the left side Strut Guide on the yellow panel of the kite. Insert the capped end of the strut into the Strut Pocket (Diagram G).

The strut guide sits just inside the strut pocket. The capped end of the middle cross strut goes into the pocket at the outside edge.

Dimension X middle cross struts fitted through strut guides into pockets and center ferrule
Diagrams G-I: Middle cross struts, strut guides, pockets, and ferrule.

Step 7: Insert the right middle cross strut

Insert the other Middle Cross Strut into the Strut Guide on the right side of the kite. Connect the end of the Middle Cross Strut to the first strut’s ferrule (Diagram H). Slide the capped end of the Middle Cross Strut into the Strut Pocket. The kite should look similar to Diagram I.

The two middle cross struts meet at the ferrule in the center. When finished, the middle cross strut spans across the middle of the kite with each outside end held in a strut pocket.

Step 8: Insert the top cross struts

Insert one Top Cross Strut into the left side Strut Guide on the top panel of the kite. Insert the capped end into the Strut Pocket (Diagram J). Insert the other Top Cross Strut into the right side Strut Guide on the opposite top panel. Connect the second spreader into the first spreader’s ferrule (Diagram K). Connect the remaining uncapped end of the Top Cross Strut into the Strut Pocket.

The top cross struts sit across the top of the kite. The close-ups label the strut guide and pocket at the outside end and the ferrule at the center joint.

Dimension X top and bottom cross struts with guides, pockets, ferrules, bridle, and daisy chain
Diagrams J-K: Top and bottom cross struts and assembled Dimension X views.

Step 9: Insert the bottom cross struts

Insert one Bottom Cross Strut into the left side Strut Guide on the bottom panel of the kite. Insert the capped end into the Strut Pocket. Insert the other Bottom Cross Strut into the Strut Guide on the right side of the kite. Connect the second Bottom Cross Strut with the ferrule on the first strut. Insert the remaining capped end of the Bottom Cross Strut into the Strut Pocket.

The bottom cross struts use the same style of strut guides, strut pockets, and center ferrule shown for the top cross struts. When both are installed, a large cross spreader runs across the bottom panel.

Flight instructions

Step 1: Attach the flying line

Attach flying line to Tow Loop.

Use 250 LB TEST LINE. You can find the bridle and daisy chain on the assembled kite drawing.

Step 2: Position the kite

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Stand with your back to the wind so your friend is downwind from you. The leading edge should be pointed toward the sky while your friend holds the kite.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Wait for the wind to catch the kite before signaling the release. Bring in the line with long steady pulls.

Step 4: Let out line

Slowly let out more line as the kite flies upward.

RECOMMENDED LINE: 250 LB TEST LINE

Optimum wind conditions for Dimension X

Beaufort scale Wind [M.P.H.] Description
CALM 0 smoke rises vertically
LIGHT AIR 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
LIGHT BREEZE 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
GENTLE BREEZE 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
MODERATE BREEZE 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
FRESH BREEZE 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
STRONG BREEZE 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle
Dimension X wind conditions chart with Beaufort scale from calm to strong breeze
Optimum wind conditions for Dimension X.

Best wind for Dimension X: 7 ~ 18 mph. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Dimension X Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.