This guide covers assembly and flight instructions for Premier 45 in. and 56 in. Flo-Tail Delta kites. This guide includes strut placement, line attachment, launch steps, and the wind chart from the manual.
Applies to: Premier 45 in. and 56 in. Flo-Tail Delta kites. See the 5 products this guide covers.
Specifications
| Model | Size (W x L) | Wind range | Frame | Line |
|---|---|---|---|---|
| 45 in. Flo-Tail Delta | 45 x 104 in. / 112 x 264 cm. | 6 ~ 20 mph | Fiberglass | Includes 50 lb. Test Line & Winder |
| 56 in. Flo-Tail Delta | 56 x 172.5 in. / 142 x 438 cm. | 6 ~ 20 mph | Fiberglass | Includes 50 lb. Test Line & Winder |
Assembly
Step 1: Unroll the kite
Unroll Kite.
Open the kite so you can see the triangular sail and the long Flo-Tail tails. The back of the kite is the side used for the frame placement shown in the back view.
Step 2: Identify the struts
Identify and organize Struts.
The struts shown in A are the Cross Strut and the Spine. The back view also labels the Leading Edge Struts in the Leading Edge Sleeves.

Step 3: Insert the spine
Insert the Spine into the Spine Pockets and close the Velcro at the bottom of the Spine Pocket.
The Spine runs up the center of the back of the kite. Put it into the Spine Pockets on the center line, then close the Velcro at the bottom of the Spine Pocket.

Step 4: Seat the leading edge struts
Make sure the Leading Edge Struts are slid all the way down the Leading Edge Sleeves.
The Leading Edge Sleeves run along the two sloping leading edges. When the struts are seated as shown, they extend down to the end of the sleeves.
Tip: This area of the sleeve should not contain struts.
Step 5: Insert the cross strut
Insert the Cross Strut into the Cross Strut Fittings.
The Cross Strut sits across the back of the kite. Its ends go into the Cross Strut Fittings shown near the leading-edge sleeves.
Step 6: Attach the flying line
Attach the flying line to the bridle loop on the front of the kite.
The front of the kite is the side with the Bridle and Bridle Loop. Attach the flying line at the Bridle Loop on the front of the kite.

Your kite is now ready to fly!
Flight instructions
Step 1: Attach the line
Attach flying line to Tow Loop.
The front view shows the Bridle and Bridle Loop on the front of the kite.
Step 2: Have a friend hold the kite
Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.
Your friend should be downwind from you, with the kite’s Leading Edge pointed towards the sky.
Step 3: Release and pull in line
As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.
Step 4: Let out line
Slowly let out more line as the kite flies upward.
Line and wind conditions
| Beaufort scale | M.P.H. | Wind description |
|---|---|---|
| Calm | 0 1 | smoke rises vertically |
| Light Air | 1 2 3 | Direction of wind shown by smoke, but not by wind vanes |
| Light Breeze | 4 5 6 7 | Wind felt on face, leaves rustle, ordinary vane moves |
| Gentle Breeze | 8 9 10 11 12 | Leaves and small twigs in constant motion; wind extends light flag |
| Moderate Breeze | 13 14 15 16 17 18 | Raises dust and loose paper; small branches move |
| Fresh Breeze | 19 20 21 22 23 24 | Small trees & leaves begin to sway; crested wavelets form on inland water |
| Strong Breeze | 25 26 27 28 29 30 | Large branches in motion; utility wire whistle; windows rattle |

Recommended line: 50 LB TEST LINEOptimum wind conditions for Flo Tail Delta: 4-18 mph.Note: Wind conditions aloft may vary considerably from those found near ground level.
Products this guide covers
45 in. Flo-Tail Delta Kite - Cheshire
45 in. Flo-Tail Delta Kite - Lime Peace
56 in. Flo-Tail Delta Kite - Liquid Checks
56 in. Flo-Tail Delta Kite - Rainbow
56 in. Flo-Tail Delta Kite - Wavy Bullets


Share:
Dragon Diamond Kite Assembly Instructions
Flying Flamingo Spinner Assembly Instructions