This guide covers assembly for Premier High Wheel Bike Spinner designs. It shows how to assemble the body frame, wheel axles, hub strut, support pole, and ground stake.

Applies to: Cat, Dog, Frog, Man, Santa, Steampunk Cat, Uncle Sam and Witch High Wheel Bike Spinners. See the 8 products this guide covers.

Premier size facts

Design Size (W x L)
Cat 24.75 in. x 30 in.
Dog; Santa 24.75 in. x 30.5 in.
Frog Not specified
Man 24.75 in. x 31 in.
Steampunk Cat 37 in. x 7.5 in.
Uncle Sam 24.75 in. x 33.5 in.
Witch 24.75 in. x 32 in.

Assembly

Step 1: Open the body sleeve

Remove your High Wheel Bike Spinner from the package. Open the Velcro seam along the bottom of the Body Sleeve.

The Body Sleeve runs along the character body, with the Main Internal Body Strut inside it. Opening the bottom seam gives access for the strut to slide into the Bike Frame Strut Assembly in the next step.

High Wheel Bike Spinner body sleeve, bike frame strut assembly, wheel struts, and thumb screws
Diagram A: Body sleeve and bike frame strut assembly

Step 2: Install the body and rear wheel struts

Slide the Main Internal Body Strut into the Bike Frame. Slide the Rear Wheel Strut into the Bike Frame and tighten the Thumb Screw. Close Velcro Seam. Strut Assembly should match Diagram A.

The Main Internal Body Strut slides downward into the Bike Frame Strut Assembly. The Front Wheel Strut and Rear Wheel Strut sit below the Bike Frame Strut Assembly when the strut assembly matches Diagram A.

Tip: Check to be sure these Thumb Screws are tightened prior to display. Loosen Thumb Screws for easy removal and storage of assembled wheels.

Step 3: Add the spinner axles

Slide the Spinner Axles onto the Wheel Struts so that the axles extend out in the same direction as the Hub Strut Receptor. Place the threaded Axle Lock Nuts on the ends of the Wheel Struts and tighten to hold the axles in place. (Diagram B)

First, slide the Spinner Axle onto the Strut Assembly; second, tighten the Axle Lock Nut. Both Wheel Axles should point to the same side as the Hub Strut Receptor.

High Wheel Bike Spinner wheel axle and axle lock nut installation with hub strut receptor
Diagram B: Spinner axle and axle lock nut

Step 4: Install the wheels

Slide a Washer onto each Axle. Slide the Large Wheel onto the Front Wheel Axle and the Small Wheel onto the Rear Wheel Axle. Slide another Washer onto each Axle. Tap the Axle Caps onto the ends of the Axles using a mallet or piece of wood. (Diagram C)

Each wheel goes between two Washers on its Axle. The Large Wheel goes on the Front Wheel Axle, and the Small Wheel goes on the Rear Wheel Axle.

High Wheel Bike Spinner wheel installation with washers and axle cap
Diagram C: Wheels, washers, and axle caps

Step 5: Attach the hub strut

Insert the Hub Strut into the Hub Strut Receptor and tighten the Thumb Screw to secure the Strut in place. (Diagram D)

The Hub Strut extends from the Upper Support Pole toward the Hub Strut Receptor. The Thumb Screw tightens at the receptor to hold the Hub Strut in place.

High Wheel Bike Spinner hub strut entering the hub strut receptor, with upper support pole
Diagram D: Hub strut and upper support pole

Step 6: Set the spinner on the support pole

Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole into the Ground Stake. Insert Upper Support Pole of assembled High Wheel Bike Spinner into the ferrule. (Diagram E)

The Lower Support Pole fits into the Ground Stake with the ferrule at the top. The assembled High Wheel Bike Spinner slides down so the Upper Support Pole goes into that ferrule.

High Wheel Bike Spinner support pole assembly with ferrule, lower pole, and ground stake
Diagram E: Support pole and ground stake

Care note

Please note: It is recommended that you take your High Wheel Bike Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

High Wheel Bike Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.