Use this guide to assemble and fly the Premier Luna Moth Kite. It covers the leading edge struts, tail strut, antenna struts, recommended line and wind conditions.

Applies to: Premier Luna Moth Kite. See the 1 products this guide covers.

Luna Moth kite specs

Model Size (W x L) Wind range Frame Line included
Luna Moth Kite 140 x 102 in. / 356 x 259 cm. 5 ~ 12 mph Pultruded Carbon Not Included

Assembly

Step 1: Unroll the kite

Unroll the kite.

Step 2: Identify the struts

Identify and organize struts. (Diagram A.)

Sort the outer leading edge struts by size: large, medium, and small. Keep the bottom struts and antenna struts separate so each group matches its label.

Luna Moth strut layout with large, medium, small, bottom and antenna struts
Diagram A: Strut layout.

Step 3: Assemble the small and medium outer leading edge struts

Insert the Small Outer Leading Edge Strut into the Medium Outer Leading Edge Strut. The uncapped end of the small strut should be inserted into the Medium strut’s ferrule. (Diagram B)

The small outer leading edge strut has its capped end at the outside end. The uncapped end goes into the ferrule on the medium outer leading edge strut.

Luna Moth small outer leading edge strut aligned with medium outer leading edge
Diagram B: Small outer leading edge into medium outer leading edge.

Step 4: Insert the assembled strut into the leading edge sleeve

Insert the capped end of the assembled strut into the Leading Edge Sleeve located at the top of the wing. (Diagram C)

Use the small-and-medium strut assembly from Step 3. The Leading Edge Sleeve is at the top of the wing, with the opening marked for the strut.

Luna Moth leading edge sleeve, dihedral, spine, tail connector and tail strut
Diagrams C-E: Leading edge struts and center Dihedral.

Step 5: Connect the large leading edge strut

Connect the Large Leading Edge Strut into the Medium Leading Edge Strut. (Diagram D)

The large strut is the next leading edge section toward the center of the kite. It connects to the medium strut while both sit along the leading edge sleeve.

Step 6: Insert the leading edge into the dihedral

Insert the remainder of the Leading Edge into the center blue Dihedral. (Diagram E)

The center blue Dihedral is at the top center of the kite, next to the Antenna Connector and the Spine. The strut end goes into the side opening of the Dihedral.

Step 7: Repeat for the opposite wing

Repeat steps 3-5 for the opposite wing.

Build the other wing with the same small, medium and large leading edge struts. Both leading edges meet at the center Dihedral.

Step 8: Insert the tail strut into the tail sleeve

Insert the capped end of the Tail Strut into the Tail Sleeve located near the bottom of the kite. (Diagram F)

The Tail Sleeve is near the bottom of the kite on the tail section. Put the capped end of the Tail Strut into the sleeve opening marked for the strut.

Luna Moth tail struts and antenna struts fitted into their connectors
Diagrams F-H: Tail struts and Antenna Connector.

Step 9: Insert the tail strut into the tail connector

Insert the opposite end of the Tail Strut into the black tail connector. (Diagram G)

The black tail connector is on the Spine above the Tail Sleeves. The tail strut end enters the connector from below.

Step 10: Insert the antenna struts

Insert the Antenna struts into each antenna. Insert the untaped end into the Antenna Connector. (Diagram H)

The Antenna Connector is at the top center of the kite, above the Dihedral. The antenna struts run into the antenna shapes, and the untaped ends go into the connector.

Tip: Antenna will cross over each other into the Antennae Connector.

Flight instructions

Step 1: Tie on the flying line

Tie flying line to Tow Loop.

Step 2: Position the kite

Have a friend stand about 75 ft. downwind from you and hold the kite with its Leading Edge pointed towards the sky.

Your friend holds the kite downwind with the Leading Edge pointed towards the sky.

Step 3: Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Step 4: Let out line

Slowly let out more line as the kite flies upward.

Recommended line: 150 LB TEST LINE.

Optimum wind conditions for Luna Moth

Beaufort category Wind [M.P.H.] Description
Calm 0 smoke rises vertically
Light Air 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
Light Breeze 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
Gentle Breeze 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
Moderate Breeze 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
Fresh Breeze 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
Strong Breeze 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle
Luna Moth optimum wind range on Beaufort wind scale
Optimum wind conditions for Luna Moth.

Best wind for Luna Moth: 5 ~ 12 mph. Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Luna Moth Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.