This guide covers assembly for Premier 19 in. Pilot Pal Spinners and 20 in. Airplane Spinners. The steps show how to install the struts, propeller, support poles and ground stake.

Applies to: 19 in. Pilot Pal Spinners and 20 in. Airplane Spinners. See the 11 products this guide covers.

Specifications

Designs Size
Cow, Monkey, Poison Dart, Tree Frog 19 in. x 11.5 in.
Gray Kitty, Ladybug 19 in. x 11.25 in.
Uncle Sam 19 in. x 12 in.
Hellcat 19.5 in. x 18 in. x 7 in.
P-40 Warhawk 20.5 in. x 16 in. x 7 in.
P-51 Mustang 20.5 in. x 19 in. x 7 in.
Spitfire 19.5 in. x 20 in. x 7 in.

Assembly

Step 1: Insert the wing strut

Insert the Wing Strut into the opening at the wing tip of the wing. Slide it through the inside of the wing and through the Channel Hole in the fabric fuselage. Guide the Wing Strut through the Main Body Strut inside the fuselage and into the other wing to the end of the wing tip. This wing tip has no opening so the strut can not pass through. You may have to shift the Main Body Strut slightly to guide the Wing Strut through. (diagram A)

The Wing Strut starts at the wing-tip Strut Opening, passes through the Channel Hole near the fuselage, and continues through the Main Body Strut. The Star Lock Hub sits on the fuselage near the channel area.

Pilot Pal and Airplane Spinner wing strut through wing, channel hole and main body strut
Diagram A: Bottom view of wings

Step 2: Insert the stabilizer strut

Insert the Stabilizer Strut into the opening on the Stabilizer. Slide it all the way through the Main Body Strut and Stabilizer to the opposite wing tip. (diagram B)

The Stabilizer Strut enters through the Strut Opening at the stabilizer end. It passes through the Channel Hole by the Main Body Strut and continues across the stabilizer.

Pilot Pal and Airplane Spinner stabilizer strut through stabilizer and main body strut
Diagram B: Bottom view of stabilizer

Step 3: Install the spinner propeller

Remove the wooden End Cap and Spacer from the Propeller Axle exiting from the front of the fuselage. Slide the Spinner Propeller onto the Axle. Replace the Spacer and wooden End Cap. (diagram C)

The Propeller Axle extends from the front of the fuselage. When the parts go back on, the Spacer is outside the Spinner Propeller and the End Cap is at the end of the axle.

Pilot Pal and Airplane Spinner propeller axle, end cap, spacer, star lock hub and upper support pole
Diagram C: Spinner propeller and upper support pole

Step 4: Attach the upper support pole

Pilot Pal Spinners: Open the Velcro seam along the bottom of the fuselage. Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and can not be removed. Close Velcro Seam. Airplane Spinners: Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and can not be removed. (diagram C)

The Plastic Tip is on the narrow end of the Upper Support Pole. The Star Lock Hub receives that tip from below the fuselage.

Tip: Pilot Pal Spinners: Push Star Lock Hub firmly onto Plastic Tip of Support Pole. NOTE: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Step 5: Set the spinner on the stake

Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole. Pilot Pal Spinners: Insert Upper Pole of assembled Pilot Pal Spinner into the ferrule. Airplane Spinners: Insert Upper Pole of assembled Airplane Spinner into the ferrule. (Diagram D)

The non-ferruled end of the Lower Support Pole goes into the Ground Stake. The ferrule is at the top of the Lower Support Pole and receives the Upper Support Pole.

Pilot Pal and Airplane Spinner on upper and lower support poles with ground stake
Diagram D: Support poles and ground stake

Care note

It is recommended that you take your Pilot Pal Spinner or Airplane Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.