This guide covers assembling the Premier Cub Airplane Spinner and setting it on its support pole. The spinner platform is an airplane, size 21 in. x 27 in.

Applies to: Airplane Spinner - Premier Cub. See the 1 products this guide covers.

Parts

Premier Cub Airplane Spinner parts layout with fuselage, wing, propeller, struts, pole, and stake
Parts layout for the PK-5200 Aircraft Spinner.
  1. Plane Fuselage x 1
  2. Spinner Propeller x 1
  3. Wing x 1
  4. Landing Gear Struts x 2
  5. Landing Gear Wheel Axle x 1
  6. Stabilizer Cross Strut x 1
  7. Support Pole x 1
  8. Ground Stake x 1

Assembly

Step 1: Install the landing gear struts and wheel axle

Insert both Landing Gear Struts through the Landing Gear Holes into the Landing Gear Pockets, located at the front of the plane. These struts should cross each other and form an “X”. Then insert the Landing Gear Wheel Axle into the two black fittings located between the two Landing Gear Pockets. (diagram A)

The Landing Gear Holes are near the Main Fuselage Hub, and the Landing Gear Pockets are at the front of the plane. The two Landing Gear Struts cross over each other between those points, forming an X.

Premier Cub Airplane Spinner landing gear struts crossing through holes into pockets
Diagram A: Landing gear struts and wheel axle.

Step 2: Attach the wing

Slide the wing “T” Fitting Thumb Screw onto the Internal Vertical Support Rod. Then insert the Landing Gear Struts into the two black Diagonal Plastic Fittings on either side of the wing. Be sure to tighten the Wing “T” Fitting Thumb Screw to secure the wing to the fuselage. Make sure the wing is fully seated on the Vertical Support Rod. (diagram B)

The “T” Fitting Thumb Screw is at the center of the wing. The two Landing Gear Struts angle up into the black Diagonal Plastic Fittings on the wing while the wing seats on the Vertical Support Rod.

Premier Cub Airplane Spinner wing attaching to landing gear struts and vertical support rod
Diagram B: Wing attachment.

Step 3: Insert the stabilizer strut

Insert the Stabilizer Strut into the opening of the Stabilizer Sleeve located underneath the stabilizer. Guide the Stabilizer Strut through the Fuselage Stabilizer Hole and to the other side. Then slide the Stabilizer Strut through the other sleeve on the other side of the stabilizer. (diagram C)

The Stabilizer Strut passes through the sleeve on one side of the stabilizer, through the Fuselage Stabilizer Hole, and then through the sleeve on the other side. The Internal Fuselage Strut label is in this area.

Tip: You may have to shift the Fuselage Stabilizer Hole slightly to line up the stabilizer strut through the hole. Shifting the Fuselage Stabilizer Hole can be accomplished by grabbing the main fuselage hub and moving the internal fuselage strut.

Premier Cub Airplane Spinner stabilizer strut passing through sleeve and fuselage stabilizer hole
Diagram C: Stabilizer strut.

Step 4: Install the spinner propeller

Remove the plastic end cap and spacer from the propeller axle exiting from the front end of the fuselage. Slide on the Spinner Propeller. Place the Spinner Propeller onto the propeller axle, then replace the spacer and the end cap. (diagram D)

Keep the spacer and plastic end cap so they can be replaced after the propeller is on the axle. The propeller mounts on the axle exiting from the front end of the fuselage.

Premier Cub Airplane Spinner propeller sliding onto the front axle
Diagram D: Spinner propeller installation.

Step 5: Set the spinner on the support pole

Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed PK-5200 Aircraft Spinner into ferrule on top of Support Pole. (diagram E)

The Support Pole goes down into the Ground Stake with the non-ferruled end first. The completed spinner’s Upper Pole Section then goes into the ferrule on top of the Support Pole.

Premier Cub Airplane Spinner on support pole inserted into ground stake
Diagram E: Ground stake and support pole.

Care note

Please note: Although your Airplane Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Premier Cub Airplane Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.