This guide covers assembly and basic flight instructions for the Premier Pterodactyl kite. It includes the spine, wing spreaders, head alignment, recommended line and wind conditions.

Applies to: Pterodactyl Kite - Black Wing. See the 1 products this guide covers.

Assembly

Step 1: Identify the struts

Identify and organize struts according to diagram A.

The spine has an upper and a lower rod. The wing spreaders include inner and outer rods, and the rod interiors have one end that connects to the Outer Wing Spreader and one end that connects to the Dihedral.

Pterodactyl strut layout with spine and wing spreaders
Diagram A: spine and wing spreader struts.

Step 2: Unroll the kite

Unroll the Pterodactyl and unfold so the back of the kite is facing up. Pull the tail down and unfold the head up from underneath the body so kite is laying flat.

Set the kite with the back side up before installing the spine. The tail is pulled down, and the head comes up from underneath the body so the body lies flat.

Step 3: Install the upper spine

Adjust the head to reveal the Velcro closure behind the neck. Slide the non-ferruled end of the Upper Spine through the loop at the base of the neck closure and connect to the internal ferrule inside the head. (diagram B)

The loop sits at the base of the neck closure. The upper end of the rod runs into the head, while the rest of the spine follows the center of the body.

Pterodactyl spine rods sliding through the neck loop and tail sleeve
Diagram B: connect the spine rods.

Step 4: Install the lower spine

Insert the Lower Spine up through the Velcro sleeve at the base of the tail and connect it to the internal ferrule on the Upper Spine Rod. (diagram B)

The lower spine enters through the sleeve at the base of the tail. The two spine segments meet along the center of the body.

Step 5: Close the spine tabs

Center the Spine on the center seam of the kite. Fasten the Velcro tab at the base of the tail. Close the Velcro strip at the base of the head over the Spine Rod. (diagram C)

The spine should lie on the center seam. When this step is finished, the closure behind the neck and the tab at the base of the tail are closed over the spine.

Pterodactyl spine centered with neck closure and tail tab closed
Diagram C: close the Velcro over the spine.

Step 6: Install the wing spreaders

Slide the Inner Wing Spreader under the fabric sleeve toward the center of the kite and slide the Outer Wing Spreader through the Velcro sleeve. Connect the Inner and Outer Wing Spreaders and insert the Inner Wing Spreader into the Dihedral on the Spine Rod. Repeat for the second wing. (diagram D)

On each wing, the inner spreader points toward the Dihedral on the Spine Rod, and the outer spreader sits near the wing end. The spreader segments join between the sleeve sections before the inner spreader goes into the Dihedral.

Tip: The Inner Wing Spreader will only connect to the internal ferrule on the Outer Wing Spreader at one end. See detail 1 for the correct way to assemble the rods.

Pterodactyl wing spreaders connected across the kite
Diagram D: install and fasten the wing spreaders.

Step 7: Fasten the wing spreader tabs

Tightly fasten the Velcro tabs at the ends of the Wing Spreaders. Be careful to apply even tension to keep the Spine centered along the seam running down the center body. (diagram D)

The Velcro tabs close at the ends of the wing spreaders. The finished spreader line runs across the kite while the spine stays centered on the body seam.

Step 8: Attach the flying line

Attach flying line to main tow loop on the front of the kite.

Step 9: Check the head

Make sure the head is perpendicular to the body (not twisted to either side). Having the head twisted will affect the way the kite flies (diagrams E and F). Your Pterodactyl is now ready to fly!

The side view shows the head set up from the body. The top view shows the head straight in line with the body, not turned to either side.

Pterodactyl side view of the head and body
Diagram E: side view of head alignment.
Pterodactyl top view with head aligned straight with the body
Diagram F: top view of head alignment.

Flight instructions

Tie the flying line

Tie flying line to Tow Loop.

Position your helper

Have a friend stand about 75 ft. downwind from you and hold the kite with its head pointed towards the sky.

Have a friend stand about 75 ft. downwind from you. The kite’s head points toward the sky while your friend holds it.

Release the kite

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls.

Let out line

Slowly let out more line as the kite flies upward.

Recommended line and wind

Beaufort scale Wind [M.P.H.] Description
Calm 0 Smoke rises vertically
Light air 1, 2, 3 Direction of wind shown by smoke, but not by wind vanes
Light breeze 4, 5, 6, 7 Wind felt on face, leaves rustle, ordinary vane moves
Gentle breeze 8, 9, 10, 11, 12 Leaves and small twigs in constant motion; wind extends light flag
Moderate breeze 13, 14, 15, 16, 17, 18 Raises dust and loose paper; small branches move
Fresh breeze 19, 20, 21, 22, 23, 24 Small trees & leaves begin to sway; crested wavelets form on inland water
Strong breeze 25, 26, 27, 28, 29, 30 Large branches in motion; utility wire whistle; windows rattle
Pterodactyl optimum wind conditions chart
Optimum wind conditions for Pterodactyl.

Recommended line: 150 LB TEST LINE. Optimum wind conditions for Pterodactyl: 5-18 M.P.H. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Pterodactyl Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.