This guide shows how to assemble, set up and fly Premier's dual-line sport kites, including the Zoomer 2.0 and the Vision.

Applies to: Premier dual-line sport (stunt) kites: Zoomer 2.0 and Vision. See the 9 products this guide covers.

Sport kite parts

Labeled parts layout of a Premier sport kite showing frame, bridle and sail
Sport Kite Diagram — parts overview (1–20).
  1. Nose / nose piece
  2. Center spine
  3. Top spreader
  4. Bottom spreader
  5. Leading edge
  6. Top leg of bridle
  7. Bottom leg of bridle
  8. Bridle out-haul
  9. Tow point loop
  10. Standoffs
  11. Center T
  12. Outer batten
  13. Top connector
  14. Lower connector
  15. Standoff holder
  16. Batten pocket
  17. Tail
  18. Wing tip (end cap / arrownock)
  19. Sail
  20. Bungi

These are the most common parts of a sport kite. Your kite may be different and not have all of these parts.

Sport kite assembly

Step 1: Prepare the leading edges and nose

Remove all contents from the kite bag. If your kite has been shipped to you, it may be necessary to pre-assemble the leading edge spars that have been separated for shipping: the lower leading edge should slide over the upper leading edge ferrule. The top and bottom connectors are made of vinyl and should also slide down to the vinyl stops glued on the leading edge tubes. If your kite has a hard plastic nose piece, insert the leading edge tubes into each side of the nose piece, making sure the tubes are inserted all the way, approximately one inch.

If your kite was shipped with the leading edges in two pieces, slide each lower leading edge over the ferrule on the upper leading edge until the tubes meet (first diagram below). Then slide the vinyl top and bottom connectors down until they rest against the vinyl stops glued on the tubes. If your kite has a hard plastic nose piece, push each leading edge tube into its side of the nose piece until it's all the way in, about one inch (second diagram).

Tip: If a tube is tight on the ferrule, twist gently while pushing—don’t force it at an angle.

Joining upper and lower leading edge tubes with a ferrule on a Premier sport kite
Leading edge ferrule connection.
Inserting leading edge tubes into a hard plastic nose piece on a Premier sport kite
Insert leading edge tubes into hard nose piece.

Step 2: Secure the wing tips

The wing tip end caps should then stretch over the bottom of the lower leading edge tubes and/or the bungi should slide underneath the arrownock, depending on which your kite has. (see fig. 18A and 20A)

At each wing tip, stretch the end cap over the bottom of the lower leading edge tube (fig. 18A). If your kite has arrownocks instead, slide the bungi underneath the arrownock (fig. 20A). Both wing tips should end up snug and fitted the same way.

Wing tip end cap stretched over lower leading edge tube on a Premier sport kite
Fig. 18A — Wing tip end cap over lower leading edge tube.
Bungee sliding underneath arrow nock at wing tip on a Premier sport kite
Fig. 20A — Bungi under arrow nock at wing tip.

Step 3: Insert the top spreader

Insert the top spreader, the shorter tube, into the top two connectors. The top spreader will fit into the connectors tightly so care should be taken when inserting or removing this tube. (see fig. 13A) If your kite has a hard plastic nose piece you will not have a top spreader and can skip this step.

Locate the two vinyl top connectors on the leading edges and push one end of the shorter spreader into each. Support the connector with one hand while sliding the tube in so you don’t twist the leading edge. If your model has a hard plastic nose and no top spreader, move on to the next step.

Tip: Insert one end first, then flex the spreader slightly to reach the opposite connector.

Top spreader inserted into top connectors on a Premier sport kite
Fig. 13A — Insert the top spreader into the top connectors.

Step 4: Fit the lower spreaders and Center T

Insert the lower spreaders into the lower two connectors. The bridle lines should always be over the spreader and come from the Center T. Depending on what type of Center T your kite has you will either: insert the lower spreader with the ferrule first and the other lower spreader should slide onto that ferrule at the Center T (see fig. 11A); or insert the lower spreaders into each of the open ends of the Center T (see fig. 11B); or your bottom spreader may be one piece and already in place. If your kite has a one-piece bottom spreader you will only need to rotate it 90 degrees into place. Please note that the tubes or ferrule will fit in the Center T tightly so care should be taken when inserting or removing these tubes. NOTE: If you have tubes with plugged ends, it is these ends that should be inserted into the Center T.

Seat the outer ends of the lower spreaders in the lower vinyl connectors on the leading edges, with the bridle lines running over the spreaders. At the Center T, either slide one spreader's ferrule into the T and push the other spreader onto that ferrule (fig. 11A), or push both spreaders into the open ends of the T (fig. 11B). If your kite has a one-piece bottom spreader, just rotate it 90 degrees into place. Everything should fit snugly without gaps.

Lower spreader with ferrule sliding into center T on a Premier sport kite
Fig. 11A — Slide one lower spreader onto the ferrule at the Center T.
Lower spreaders inserted into both open ends of center T on a Premier sport kite
Fig. 11B — Insert both lower spreaders into the open ends of the Center T.

Step 5: Install standoffs and any outer battens

You will note that there is a set of standoffs attached to the kite and, depending on your model of kite, a set of battens. Insert the standoffs into the standoff holders on the lower spreaders (see fig. 15A). Please note outer battens may be in the fold of the nose material, out towards the leading edge of the kite. Insert battens in the outside batten pockets on the kite and then into the holder on the lower spreader (see fig. 16A). Adjust the standoff holders so that the standoffs are perpendicular to the lower spreaders. Never fly without these in place. If your kite has removable outer battens, store them in the nose material when done flying.

Push the end of each standoff into its standoff holder on the lower spreader until it seats (fig. 15A). If your kite has outer battens, slide each one into the outside batten pocket on the sail, then seat its other end in the holder on the lower spreader (fig. 16A). Adjust the standoff holders so each standoff sits at a right angle to the lower spreader. Never fly without the standoffs in place.

Tip: If your kite has removable outer battens, store them in the nose material when you're done flying.

Standoff rod inserting into standoff holder on lower spreader of a Premier sport kite
Fig. 15A — Insert the standoff into the standoff holder.
Outer batten inserting into batten pocket near leading edge on a Premier sport kite
Fig. 16A — Outer batten into the batten pocket near the leading edge.

Step 6: Final frame and bridle check

Make sure that all tubes are fully inserted into the connectors. Also check that the bridle lines are over the spreaders, properly tightened around the leading edges and the spine by the Center T.

Go over the kite from nose to tips confirming every connector is fully home on its tube and nothing is halfway out. Verify the bridle wraps and knots sit neatly at the leading edges and at the Center T and that both sides look the same.

Step 7: Adjust the leech line if needed

Your kite may have what is called a leech line that runs through the sewn hem along the bottom edge of the sail and attaches to the wing tips. The purpose of this line is to keep the kite quiet. The line wraps around the end nock and has the bungi secured over it with a vinyl cap. If your kite becomes noisy the tension of this line can be adjusted by removing the vinyl cap and carefully unwrapping the line. Adjust the tension then secure the line again. Be careful not to over tighten the leech line as it will pull the wing tips in too far and change the flight characteristics. The line should just be snug only.

Look along the trailing edge hem for the leech line and where it anchors at each tip under a cap. To quiet flutter, take off the small cap, unwrap or wrap the line slightly to change length, then re-cap. Stop as soon as the line is just snug—overtightening pulls the tips inward and alters how the kite flies.

Step 8: Add tail weight (if your kite has a weight pocket)

Your kite may also have a weight pocket sewn into the tail of the kite. Weight is added to increase the trick capability. To use this pocket, undo the Velcro at the tail. It is designed to hold up to 4 quarters (30 gms). Insert your weights into the pocket and re-secure the Velcro.

Open the Velcro closure at the tail and slide your weights into the pocket. Keep the load within the 4-quarter (about 30 g) limit and close the Velcro firmly so the weight can’t shift or fall out during flight.

Tip: Start with no weight and add gradually until the feel suits you.

Bridle and flying lines

Adjust the bridle tow point (if needed)

Your bridle has been factory set and marked for your convenience. If the tow point loop has shifted it can be corrected. To make changes, pull the top leg and bottom leg to open the larks head knot. Slide the tow point above or below the mark. For less pull and more height, move the tow point towards the nose. This is good for faster climbing in light winds. For more pull and fast turns, move the tow point towards the tail. Make small changes; 1/8 inch makes a big difference in flying performance.

Find the mark on the bridle near the tow point and open the lark’s head by pulling the two legs apart. Slide the tow point loop a tiny amount to the nose for lighter pull and better climb, or toward the tail for stronger pull and quicker turns. Re-snug the knot at the new spot.

Prepare lines if your kite comes with plastic handles

Make sure your lines are fully unwound and, most important, equal in length before attempting to launch your kite. If one line is longer than the other, simply wrap the excess line around the plastic “T” knob on the center of the handle.

Unwind both lines completely and lay them out side by side to compare their lengths. If one is longer, take up the extra by wrapping it around the plastic T knob at the center of that handle until both lines match exactly.

Tip: Even lines make the kite track straight—check again after your first few flights.

Prepare lines if your kite comes with a winder and straps

You have a high-performance Spectra line set. Check to be sure that the lines are equal lengths and sleeved on both ends. Let out all of your line before attempting to launch your kite. If at any time the Spectra lines don’t appear equal in length, an adjustment should be made. Untie the sleeving loop knots on one end of the longer line and slide the sleeving down the line until it is adjacent to the other and then re-tie the loop. Be careful not to pull the sleeve off the Spectra. Cut off any excess line. Larks head knots (see fig. 9A) are used to connect the line to both the bridle tow point loop and flying straps for easy connection and removal.

Unwind the whole set and lay the two lines side by side to check that they're the same length and sleeved at both ends. If one is longer, untie the sleeving loop knot at one end of that line, slide the sleeving along until the loop lines up with the end of the other line, then re-tie the loop and cut off the excess line. Lark's head knots connect the lines to the bridle tow point loops and to the flying straps.

Tip: Don't pull the sleeve off the end of the Spectra line while you're sliding it.

Connect the flight lines

Your kite is now fully assembled and ready to fly. All you need to do is attach your flying lines and wrist straps. Attach fly lines using a larks head or cinch type knot (see fig. 9A).

Attach each flying line to a bridle tow point loop on the kite with a lark's head knot, as shown in fig. 9A: the left-hand line to the left side of the kite as you face it, and the right-hand line to the right side. Attach the other ends to your wrist straps or handles the same way, and check that the lines aren't crossed.

Tip: After connecting, walk back and apply light tension—both lines should feel exactly the same length.

Larks head knot attaching flying line to bridle tow point with marks on a Premier sport kite
Fig. 9A — Lark’s head attachment of flying line to the bridle tow point.

Learning to fly

Step 1: Solo launching setup

With first flights it is easiest to have a helper toss the kite into the air. When flying alone, stake your handles or straps to the ground with an old screwdriver or tent stake or anything that you can push into the ground. With the lines completely unwound, attach your kite. With the lines anchored and under tension, the kite will stand on its wing tips. Tilt the nose of the kite back 45 degrees so the kite doesn’t accidentally self-launch. Lines must be out and adjusted to equal length before launching. Make sure the person holding the kite is behind it and pointing the nose skyward. Keep your hands forward and parallel just before launch.

Pick a clear area and lay out the lines directly downwind. Anchor the straps, connect to the bridle, and stand the kite on its wing tips with the nose leaning back. If you have a helper, have them stand behind the kite holding the nose up while you keep both hands even and forward.

Tip: Before you try to launch, sight down both lines to confirm they’re not crossed or snagged.

Solo launch step 1 setup with lines equal and helper behind the Premier sport kite
Step 1 — Lines equal; helper behind the kite with nose skyward.

Step 2: Launch the kite

To launch the kite, pull both lines until the kite stands up straight. Then pull back both lines with equal tension and the kite will launch straight into the sky. Remember to return both hands forward. Wind must be at the flyer’s back. To take off, tell your friend to release the kite. At the same time pull back on both lines with equal tension to launch the kite. Immediately return both hands forward.

Stand with the wind at your back, facing the kite. Bring the kite upright, then give an even, firm pull on both lines and release back to neutral as the kite climbs. Keep your hands together to go straight up.

Tip: If the kite drifts to one side as it climbs, pull gently on the opposite handle to straighten it.

Solo launch step 2 pulling both lines to take off with wind at the flyer’s back on a Premier sport kite
Step 2 — Pull both lines to launch; wind at your back.

Basic control

Steer left, straight, and right

On your first launch, keep your hands next to each other and let your kite ascend as high as possible. If your kite wanders to one side, make corrections by pulling on the opposite control handle. A stunt kite turns toward the same direction it is pulled: pull right—the kite turns right; pull left—the kite turns left. As a beginner, concentrate on steering toward the sky and maintaining plenty of altitude before doing complex stunts. The most common problem a beginner has is over-controlling their kite. Only a few inches of pull is needed for maneuvering. If you continue to pull to one side, your kite will make a loop—the further you pull back, the tighter the loop will be. At any point in the loop or turn, you can even out your hands and the kite will continue in the direction the nose is pointing. After doing loops, your control lines will be twisted. This may seem troublesome, but don’t worry—you still have control of your kite. To untwist, simply fly loops in the opposite direction.

Neutral, even hands make the kite track straight ahead. A short pull on the right hand turns the kite right; a short pull on the left turns left, as shown in the diagram. Use small inputs—just a few inches—and even your hands to exit a turn. If your lines twist after loops, fly a loop the other way to unwind them.

Tip: Think “tap” not “yank”—small, quick pulls give smoother turns and better control.

Hand inputs for turn left, fly straight, and turn right with a Premier sport kite
Control — Pull left, hands even, pull right.

Wind window and landings

Understand and use the wind window

The wind window is an area of the sky where sport kites maneuver. The window is shaped like a half dome. The size of the window changes with the wind speed—higher winds produce larger windows. Your kite will react differently in various parts of the window. The Power Zone is where your kite will pull the most and have the most speed; this is where you will have the most success launching your kite. On the Edge the kite is angled away from the direct wind. This lowers the speed and pull of the kite and makes landings easier. The extreme edge is the point where the kite can’t move forward anymore. In lighter winds your kite becomes a victim of gravity and sinks to the ground. In higher winds your kite can hover on the edge and retain its position in the sky.

Picture a half dome in front of you: the center is the Power Zone and the outer rim of the dome is the Edge. Launch in the middle where the kite has the most drive, then practice moving to the edges where it slows and pulls less. In strong wind you can park the kite near the edge; in light wind it will sink toward the ground there.

Tip: The Power Zone is the easiest area to launch in, and the Edge is the easiest area to land.

Wind window dome showing power zone and edge positions for a Premier sport kite
Wind Window — Power Zone and Edge.

Land smoothly

You’ll soon notice that as the kite flies to the edge of the window, it slows down and eventually stalls. Maneuver the kite to the outermost edge about a foot off the ground and run toward the kite while throwing your arms forward. Your lines will go slack and the kite will gently land.

Guide the kite to the far left or right edge of the window, about a foot off the ground. Then step or jog toward the kite while pushing both hands forward, so the lines go slack and the kite settles gently onto the ground.

Wing-tip landing (advanced) and relaunch

For an advanced maneuver, try landing your kite on its wing tips. When your kite is about a foot off the ground, rotate the nose skyward and run forward, keeping your hands in front and the line equal. The kite will lose wind and land on its wing tips. You are now ready to relaunch.

Bring the kite low at the edge, then lift the nose and give a quick step forward with hands even so both lines slack at the same time. The kite will settle upright on its two wing tips, ready for a clean pull on both lines to relaunch.

Before you fly

  • Find a flying field that is large, flat and wide open. Avoid large obstructions like trees or buildings that create turbulence and reduce wind near the ground. Determine wind direction by tossing grass or sand and set up with the wind at your back. Winds around 8–12 mph are ideal for learning how to fly your Premier Sport Kite.
  • Think safety: avoid flying near cars, people, power lines and airports. Stunt kites can move at high speeds and can damage people and property. Both the kite and flying lines are potential hazards—the line can hit or cut with high force while moving at high speeds. Use your stunt kite with extreme care; flying safely is your sole responsibility.

Zoomer 2.0 and Vision specs

Model Dimensions Wind range Line included
Zoomer 2.0 46 x 21 in. (117 x 53.25 cm) 6–20 mph Flying line included
Vision 63 x 29 in. (159 x 73 cm) 5–10 mph 100 ft. low-stretch polyester line included

Beaufort scale

Wind speed (mph) Description Specifications for use on land
0–1 Calm Calm; smoke rises vertical.
1–3 Light air Direction of wind shown by smoke drift, but not by wind vanes.
4–7 Light Breeze Wind felt on face; leaves rustle; ordinary vanes moved by wind.
8–12 Gentle Breeze Leaves and small twigs in constant motion; wind extends light flag.
13–18 Moderate Breeze Raises dust and loose paper; small branches are moved.
19–24 Fresh Breeze Small trees in leaf begin to sway; crested wavelets form on inland waters.
25–31 Strong Breeze Large branches in motion; whistling heard in telegraph wires; umbrellas used with difficulty.

Products this guide covers

Download the original manual

Premier Sport Kite Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.