This guide covers assembly and mounting for Premier WindGarden telescoping poles. It applies to Flex and Heavy Duty windsock poles in the listed sizes.

Applies to: Flex Windsock Pole 10, 13, 16 and 19 Ft.; Heavy Duty Windsock Pole 10, 13, 16, 19, 22, 26, 29 and 32 ft. See the 12 products this guide covers.

Ground mount compatibility

Pole Ground mount noted by Premier
Flex 10 Ft. and 13 Ft. 1/2 in. Fiberglass Ground Mount
Flex 16 Ft. 5/8 in. Fiberglass Ground Mount
Flex 19 Ft. 5/8 in. Fiberglass Ground Mount or 5/8 in. Steel Ground Mount
Heavy Duty 10 ft. and 13 ft. 5/8 in. Fiberglass Ground Mount or 5/8 in. Steel Ground Mount
Heavy Duty 16 ft. and 19 ft. 5/8 in. Steel Ground Mount
Heavy Duty 22 ft., 26 ft., 29 ft. and 32 ft. 5/8 in. Steel Ground Mount; for more extreme conditions, Premier recommends a 1 to 1-1/2 in. pipe at least 48 in. long

These poles do not include a ground stake.

Assembly

Step 1: Remove the top endcap

Remove the endcap from the top of your Telescoping Pole. For ease of collapsing and storing your pole, do not lose this endcap. (diagram A)

The top endcap comes off the narrow open end at the top of the pole.

Telescoping Pole with the top endcap removed from the open end
Diagram A: Remove top endcap.

Step 2: Extend the pole sections

Tilt the open end of the pole towards the ground and extend one section at a time by pulling until the base of each section is securely wedged into the top opening of the piece below it. Pull each section to extend pole. Make sure each section is fully extended so the pole will not collapse. (diagram B)

Work one section at a time from the open end, following the arrows outward. The base of each extended section sits in the top opening of the section below it when it is wedged in place.

Telescoping Pole sections pulled outward to extend the pole
Diagram B: Pull each section to extend the pole.

Step 3: Attach your Premier product

Attach your Premier product to the pole. Attach strings or swivels to the loop at the top of the pole to hold product in place. Note that banners will need to have the pole slid into the sleeve along the edge of the banner before tying the strings to the loop. Banners also have strings at the bottom of the sleeve that should be tied to the clip near the base of the pole. (diagram C) Attach product to metal loop using the strings or swivels. For Banners: Slide pole through sleeve before tying strings to loop. For Banners: Tie strings at the bottom of the sleeve to the clip on the pole.

The loop is at the top of the pole, and the clip is near the base of the pole. If you are putting up a banner, the sleeve runs along the banner edge with the pole through it before the top strings are tied.

Telescoping Pole top loop and base clip for attaching strings or swivels
Diagram C: Attach product to the metal loop and tie banner strings to the clip.

Step 4: Mount the pole

Drive a ground mount (not included in the pole packaging) into the ground. Remove the bottom Endcap from the pole and slide the pole over the ground mount. For ease of collapsing and storing your pole, do not lose this endcap. (diagram D) Drive ground mount into ground. (ground mount must be bought separately) Remove bottom Endcap. Slide pole onto ground mount.

The ground mount is driven into the ground, with the pole lowered over it after the bottom endcap is removed. When mounted, the pole stands over the ground mount at ground level.

Telescoping Pole sliding onto a ground mount with banner and windsock examples
Diagram D: Drive the ground mount into the ground and slide the pole onto it.

Products this guide covers

Download the original manual

Telescoping Pole Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.