This guide shows how to assemble and install Premier's WhirliGig Spinners (the 10 to 22 in. designs). The spinners have SunTex fabric wings and mount on a support pole set into a ground stake.
Applies to: Premier WhirliGig Spinners, 10 to 22 in. designs. See the 29 products this guide covers.
Not your model? If your WhirliGig has a thumb screw on the frame and a one-piece support pole, it uses the Large WhirliGig Spinner instructions.
Assemble your WhirliGig Spinner
Step 1: Slide the Spinner Axle through the frame
Slide the long side of the Spinner Axle through the Frame. The ends of the Axle should be equally far from the WhirliGig Body. (Diagram A)
Push the long, plain end of the axle through the Frame first. Center it so the same amount of axle sticks out on both sides of the WhirliGig Body. The inset in Diagram A shows about 3.5 in. on each side when centered. The side of the axle with the Stops ends up just outside the body.

Step 2: Install washers, spinner set(s) and end caps
Set the Spacer, two Washers and one spinner set aside. Slide one Washer onto the side of the Axle with the Stops. Decide which way you want the arms or wings to face and slide one set onto the Axle followed by the remaining Washer. Carefully pound the End Cap onto the Axle. Repeat with the remaining parts on the other side of the Axle, making sure to place the Spacer closest to the WhirliGig Body. (Diagrams B & C)
On the side of the axle that has the Stops, add a Washer first. Choose the orientation you want for the wings/arms and slide a Spinner Set onto the axle, then add the second Washer and tap on an End Cap to secure that side. On the other side, slide on the Spacer first so it sits closest to the WhirliGig Body, then a Washer, the second Spinner Set, the last Washer and the second End Cap (Diagram C). When done, each Spinner Set sits between two Washers, with an End Cap fully seated on each end of the axle.


Step 3: Attach the Upper Support Pole to the Star Lock Hub
Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and can not be removed. (Diagram C)
Line up the Star Lock Hub with the plastic tip at the top of the Upper Support Pole, as shown. Press the hub straight down over the tip until it locks in place and can't be pulled back off. This hub assembly sits at the center of the WhirliGig Body between the two Spinner Sets. Arrows in Diagram C show the straight-down motion.
Tip: To make insertion easier, place the bottom of the Support Pole on a hard, flat surface and push down on the Star Lock Hub.
Step 4: Install the ground stake and poles
Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole. Insert the Upper Support Pole of assembled WhirliGig Spinner into the ferrule (Diagram D).
Push the Ground Stake firmly into the soil. Insert the plain (non-ferruled) end of the Lower Support Pole into the Ground Stake. Join the poles by sliding the Upper Support Pole into the Ferrule on the lower pole so the assembly stands upright, as shown in Diagram D. The spinner should sit above the ferrule with the wings free to turn.

Care and weather
It is recommended that you take your WhirliGig Spinner inside during storms and harsh weather to preserve its durability.
Products this guide covers
10 in. WhirliGig Spinner - Party Cups
10 in. WhirliGig Spinner - Pumpkin
12 in. WhirliGig Spinner - Chicken
12 in. WhirliGig Spinner - Crab
12 in. WhirliGig Spinner - Easter Bunny
12 in. WhirliGig Spinner - Island Parrot
13 in. WhirliGig Spinner - Bumble Bees
13 in. WhirliGig Spinner - Frog
13 in. WhirliGig Spinner - Sailboat
15 in. WhirliGig Spinner - Sledding
18 in. WhirliGig Spinner - Fisherman
18 in. WhirliGig Spinner - Leprechaun
18 in. WhirliGig Spinner - Patriotic Eagle
20 in. WhirliGig Spinner - Canoe
20 in. WhirliGig Spinner - Kayak
20 in. WhirliGig Spinner - Nutcracker
20 in. WhirliGig Spinner - Scarecrow
20 in. WhirliGig Spinner - Victorian Swimmer
22 in. WhirliGig Spinner - Skeleton
WhirliGig Spinner - 12 in. Maryland Crab
WhirliGig Spinner - 21 in. Wine A Bit
WhirliGig Spinner - Buff Chicken
WhirliGig Spinner - Wine A Bit More
17 in. WhirliGig Spinner - Brown Owl
18 in. WhirliGig Spinner - Blue Jay
19 in. WhirliGig Spinner - Loon
20 in. WhirliGig Spinner - Canadian Goose
20 in. WhirliGig Spinner - Fireman
WhirliGig Spinner - 18 in. Baby Sea Turtle


Share:
Easy Flyer Kite Assembly Instructions
Premier Sport Kite Instructions