This guide covers assembly for the Red Baron Tri-Plane Kite, including the airplane body, wing brace struts, propeller, and flying line attachment.

Applies to: Red Baron Tri-Plane Kite. See the 1 products this guide covers.

Assembly

Step 1: Remove the kite and set parts aside

Remove the kite from the bag and set aside the Wing Brace Struts and Propeller. Note: Wing Brace Struts may be packaged inside the Airplane Body.

Set the Propeller and Wing Brace Struts where you can reach them before you rotate the Airplane Body. The Propeller and Wing Brace Struts are labeled separately from the kite.

Red Baron Tri-Plane Kite diagram A with propeller, wing brace struts, and airplane body
Diagram A: Propeller, Wing Brace Struts, and Airplane Body position.

Step 2: Rotate the Airplane Body

Rotate the Airplane Body so that it is perpendicular to the Wings. (diagram A)

The Airplane Body is the center body section of the kite. Rotate it before hooking the Nose Cross Strut and Lower Body Strut into the body opening.

Step 3: Hook the Nose Cross Strut

Hook the Nocks at the ends of the Nose Cross Strut into the holes on the sides of the Airplane Body opening. (diagram B)

Work at the Airplane Body opening. The Nose Cross Strut runs side to side across the opening, with a nock at each side.

Red Baron Tri-Plane Kite diagram B showing Nose Cross Strut nocks at the Airplane Body sides
Diagram B: Hook Nose Cross Strut Nocks into the openings on the sides of the Airplane Body.

Step 4: Hook the Lower Body Strut

Hook the Nock at the end of the Lower Body Strut into the hole at the bottom of the Airplane Body opening. (diagram C)

The Lower Body Strut sits below the Nose Cross Strut at the Airplane Body opening. Its nock goes into the bottom opening of the body.

Red Baron Tri-Plane Kite diagram C showing Lower Body Strut nock at the bottom opening
Diagram C: Hook Lower Body Strut Nock into the opening on the bottom of the Airplane Body.

Step 5: Install the Wing Brace Struts

Position one Wing Brace Strut between the fabric upper and lower wing connector and the pre-installed Wing Brace Strut. Insert one end of the Wing Brace Strut into the fitting at the front of the top wing. Arch the Strut to fit the other end into the fitting at the back of the bottom wing. Repeat with the remaining Wing Brace Struts. (diagram D)

Use the open fittings on the wings. The Wing Brace Struts cross between the top and bottom wings, with one end at the front of the top wing and the other end at the back of the bottom wing.

Tip: Wing Brace Strut should be on the outside of the pre-installed Strut.

Red Baron Tri-Plane Kite diagram D showing Wing Brace Struts installed between the wings
Diagram D: Insert Wing Brace Struts into the open fittings on the wings.

Step 6: Install the Propeller

Remove the End Cap from the Center Body Strut and slide the Propeller onto the Strut. Replace the End Cap. (diagram E)

The Center Body Strut is the upright strut above the Airplane Body. Slide the Propeller down onto that strut, then put the End Cap back on above it.

Red Baron Tri-Plane Kite diagram E showing propeller installed on the Center Body Strut
Diagram E: Slide Propeller onto Center Body Strut; replace End Cap.

Step 7: Attach the flying line

Attach flying line to tow loop on the front of the kite.

Optimum wind conditions

Red Baron Tri-Plane Kite wind chart showing optimum wind from 8 to 18 M.P.H.
Optimum wind conditions for Triplane Kite.

Optimum wind conditions for Triplane Kite: 8-18 M.P.H. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Red Baron Tri-Plane Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.