This guide covers assembly for the Stearman Bi-Plane Kite. It follows the manufacturer’s steps for positioning the airplane body, installing the struts and propeller, and choosing the wind range.

Applies to: Premier Stearman Bi-Plane Kite. See the 1 products this guide covers.

Assembly

Step 1: Remove the kite and set aside parts

Remove the kite from the bag and set aside the Wing Brace Struts and Propeller.

The loose parts called out for this kite are the Propeller and the Wing Brace Struts. Keep them nearby before you rotate the Airplane Body and hook the struts into place.

Tip: Wing Brace Struts may be packaged inside the Airplane Body.

Step 2: Rotate the Airplane Body

Rotate the Airplane Body so that it is perpendicular to the Wings. (diagram A)

When positioned as shown, the Wings run side to side and the Airplane Body extends at a right angle from them. The Center Body Strut is at the top of the body.

Stearman Bi-Plane Kite body perpendicular to wings with propeller and Wing Brace Struts set aside
A. Airplane Body perpendicular to the Wings, with Propeller and Wing Brace Struts.

Step 3: Hook the Nose Cross Strut Nocks

Hook the Nocks at the ends of the Nose Cross Strut into the holes on the sides of the Airplane Body opening. (diagram B)

The Nose Cross Strut runs across the Airplane Body opening. Each Nock sits at one side opening.

Stearman Bi-Plane Kite Nose Cross Strut Nocks hooked into side openings of the Airplane Body
B. Hook Nose Cross Strut Nocks into the side openings.

Step 4: Hook the Lower Body Strut Nock

Hook the Nock at the end of the Lower Body Strut into the hole at the bottom of the Airplane Body opening. (diagram C)

The Lower Body Strut runs down from the Nose Cross Strut area toward the bottom of the Airplane Body opening. Its Nock fits into the bottom opening.

Stearman Bi-Plane Kite Lower Body Strut Nock hooked into the bottom Airplane Body opening
C. Hook Lower Body Strut Nock into the bottom opening.

Step 5: Install the Wing Brace Struts

Position one Wing Brace Strut between the fabric upper and lower wing connector and the pre-installed Wing Brace Strut. Insert one end of the Wing Brace Strut into the fitting at the front of the top wing. Arch the Strut to fit the other end into the fitting at the back of the bottom wing. Repeat with the second Wing Brace Strut on the other side. (diagram D)

Use the open fittings on the wings: one at the front of the top wing and one at the back of the bottom wing. The added Wing Brace Strut crosses the pre-installed Strut between the upper and lower wings.

Tip: Wing Brace Strut should be on the outside of the pre-installed Strut.

Stearman Bi-Plane Kite Wing Brace Struts crossing between upper and lower wing fittings
D. Insert Wing Brace Struts into the open fittings on the wings.

Step 6: Install the Propeller

Remove the End Cap from the Center Body Strut and slide the Propeller onto the Strut. Replace the End Cap. (diagram E)

The Propeller slides down onto the upright Center Body Strut from above. The End Cap goes back onto the top of the Center Body Strut after the Propeller is in place.

Stearman Bi-Plane Kite Propeller sliding onto the Center Body Strut with End Cap above
E. Slide Propeller onto Center Body Strut and replace End Cap.

Step 7: Attach the flying line

Attach flying line to tow loop on the front of the kite.

Optimum wind conditions

Beaufort scale Wind [M.P.H.]
Calm 0
Light Air 1 2 3
Light Breeze 4 5 6 7
Gentle Breeze 8 9 10 11 12
Moderate Breeze 13 14 15 16 17 18
Fresh Breeze 19 20 21 22 23 24
Strong Breeze 25 26 27 28 29 30
Stearman Bi-Plane Kite wind chart showing optimum range from 8 to 18 mph
Optimum wind conditions for Biplane Kite.

Optimum wind conditions for Biplane Kite: 8-18 mph. Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Stearman Bi-Plane Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.