Use this guide to assemble and fly Premier T-Delta Orbit kites. It covers the Cool Orbit, Rainbow Orbit and Warm Orbit designs.

Applies to: T-Delta Kite - Cool Orbit, Rainbow Orbit and Warm Orbit. See the 3 products this guide covers.

T-Delta kite specs

Models Size (W x L) Wind range Line Frame
Cool Orbit, Rainbow Orbit, Warm Orbit 150 x 283 in. / 330 x 720 cm. 6 ~ 18 mph 150 lb. Test Line Recommended; not included Fiberglass

Assembly

Step 1: Unfold the kite and sort the struts

Unfold the kite and lay it facedown on the ground. Set aside all struts. The Spine and Cross Strut parts will be grouped separately for you. The assembled Cross Strut is slightly longer than the assembled Spine. The parts to both Leading Edge Struts are grouped together.

You should have separate groups for the Spine, Cross Strut and Leading Edge Struts. The Cross Strut and Spine are the center struts shown beside the kite, and the Leading Edge Struts are the grouped struts for the two leading-edge sleeves.

Step 2: Install the spine

Assemble the Spine and slide it through the opening at the base of the Spine Sleeve all the way up into the Nose of the kite. Fasten Velcro tab.

The Spine Sleeve runs up the center of the kite to the Nose. The Velcro tab is at the base of that sleeve.

Step 3: Install the cross strut

Assemble the Cross Strut and slide it through the webbing loop located along the Spine. Insert each end into one of the Pockets along the Leading Edge.

The webbing loop is located along the Spine near the center of the kite. Each end of the Cross Strut sits in a Pocket along the Leading Edge.

Step 4: Install the leading edge struts

Assemble one of the Leading Edge Struts and slide it all the way through the Leading Edge Sleeve. Securely close the Velcro tab. Repeat with the remaining Leading Edge Strut.

Each Leading Edge Sleeve runs along one slanted outside edge of the kite. Close the Velcro tab after the strut is inside the sleeve, then do the same on the other leading edge.

T-Delta kite with spine, cross strut, leading edge struts, sleeves and Velcro tabs
Assembly diagram: Spine, Cross Strut and Leading Edge Struts

Flying

Step 1: Tie on the flying line

Tie flying line to tow loop on the front of the kite.

Use the tow loop on the front of the kite for the flying line. The recommended line is 150 lb test line.

Step 2: Position the kite for launch

Have a friend stand about 75 ft. downwind from you and hold the kite with its Nose pointed towards the sky.

The Nose of the kite points toward the sky before release.

Step 3: Release and climb

As the wind catches the kite, signal your friend to release it while you bring in the line with long steady pulls. Slowly let out more line as the kite flies upward.

Wind conditions and line

Beaufort scale Wind description Wind [M.P.H.]
Calm smoke rises vertically 0
Light Air Direction of wind shown by smoke, but not by wind vanes 1, 2, 3
Light Breeze Wind felt on face, leaves rustle, ordinary vane moves 4, 5, 6, 7
Gentle Breeze Leaves and small twigs in constant motion; wind extends light flag 8, 9, 10, 11, 12
Moderate Breeze Raises dust and loose paper; small branches move 13, 14, 15, 16, 17, 18
Fresh Breeze Small trees & leaves begin to sway; crested wavelets form on inland water 19, 20, 21, 22, 23, 24
Strong Breeze Large branches in motion; utility wire whistle; windows rattle 25, 26, 27, 28, 29, 30

Optimum wind conditions for T-Delta: 6 ~ 18 mph. Recommended line: 150 lb test line. Note: Wind conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

T-Delta Kite Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.