This guide covers assembly for Premier 19 in. and 25 in. Tricycle Spinner designs. Use the size-specific note in Step 6 for the support pole and ground stake setup.

Applies to: 19 in. and 25 in. Boy, Cat, Dog, and Girl Tricycle Spinners. See the 8 products this guide covers.

Product sizes

Models Size (W x L)
19 in. Boy, Cat, Dog, Girl 19 in. x 20.25 in.
25 in. Boy, Cat, Dog, Girl 25 in. x 29.5 in.

Before assembly

Please note: Although your Tricycle Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Assembly

Step 1: Attach the upper support pole to the star lock hub

Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and can not be removed. (diagram A)

The plastic tip is the narrow end shown at the top of the Support Pole. The Star Lock Hub sits above it, with the opening aligned over the plastic tip.

Tip: Push Star Lock Hub firmly onto Plastic Tip of Support Pole. To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Tricycle Spinner frame with star lock hub, wheel axles, washers, and end caps
A. Star lock hub, wheel axle fittings, and wheel assemblies.

Step 2: Install the wheel axles

Loosen the Thumb Screws on the Wheel Axle Fittings. Slide the Single Wheel Axle onto the Vertical Strut of the Tricycle Frame. Slide the Double Wheel Axle onto the Diagonal Strut of the Tricycle Frame. Tighten Thumbscrews. Note: It is important that the longer end of the Double Wheel Axle extends in the same direction as the Single Wheel Axle. This will make the Front Wheel centered between the two Back Wheels once assembly is complete. (diagram A)

The Single Wheel Axle is on the vertical strut at the front wheel position. The Double Wheel Axle is on the diagonal strut and extends out to both sides for the two back wheels.

Tip: The Thumb Screw on your spinner may be on the opposite side of the Fitting.

Step 3: Assemble the front wheel

Complete the Front Wheel assembly on the Single Wheel Axle by sliding the parts on in the following order: Washer, Large Wheel, Washer, End Cap. You will need to tap the End Cap onto the Axle using a mallet or piece of wood. (diagram A)

The Large Wheel goes on the Single Wheel Axle. A Washer is on each side of the wheel, with the End Cap on the outside end of the axle.

Step 4: Assemble the rear wheels

Complete the Rear Wheel assembly on the Double Wheel Axle by sliding the parts on both sides in the following order: Washer, Small Wheel, Washer, End Cap. (diagram A)

Repeat the same order on both sides of the Double Wheel Axle. The Small Wheels sit on the two axle ends at the back of the tricycle frame.

Step 5: Add the fabric body sleeve

Slide the Fabric Body Sleeve onto the Tricycle Frame and insert the Internal Body Strut into the top of the Star Lock Hub. Attach all Velcro Tabs inside the Body Sleeve to the tabs on the Tricycle Frame. (diagram B)

The Fabric Body Sleeve lowers over the frame from above. The Internal Body Strut is vertical inside the body sleeve and its lower end goes into the top of the Star Lock Hub.

Tricycle Spinner fabric body sleeve lowering onto the frame and star lock hub
B. Fabric body sleeve and internal body strut.

Step 6: Set the spinner on the ground stake

25 in. designs: Drive Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed Tricycle Spinner into ferrule on top of Support Pole. (diagram C)

On the 25 in. assembly, the Lower Support Pole has the Ground Stake at the bottom and the Ferrule at the top. The completed spinner’s Upper Support Pole points down into the ferrule.

Tip: 19 in. designs: Drive Ground Stake into ground and insert the Support Pole of assembled Tricycle Spinner into the Ground Stake.

Tricycle Spinner on upper and lower support poles with ferrule and ground stake
C. Support pole, ferrule, and ground stake setup.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.