This guide covers assembly for the Premier 30 in. Unicorn Bike Spinner. It follows the manufacturer’s steps for the body sleeve, basket sleeve, axles, spinner wheels, ground stake and support pole.

Applies to: 30 in. Bike Spinner - Unicorn. See the 1 products this guide covers.

Assembly

Step 1: Insert the Tail Stiffener

The decorative elements of your Unicorn Bike is shipped in two sections: the Body Sleeve and the Basket Sleeve (Diagram B). The Main Internal Body Strut Assembly is already sewn inside of the Body Sleeve. First fold back the fabric of the Body Sleeve to insert the Tail Stiffener rod, which is attached to the Bike Frame Strut Assembly (Diagram A).

Fold back the Body Sleeve at the tail area so the Tail Stiffener can slide into the Tail. The Main Internal Body Strut stays inside the Body Sleeve while the Tail Stiffener enters the Tail.

Unicorn Bike Spinner Tail Stiffener inserted into the Tail of the Body Sleeve
A: Insert the Tail Stiffener into the Tail.

Step 2: Connect the body strut to the rear ferrule

With the Tail Stiffener inside the Tail of the Body Sleeve, connect the Main Internal Body Strut to the Rear Ferrule of the Bike Frame Strut Assembly (Diagram B). You will need to rotate the Body Sleeve clock-wise to align and connect the Main Internal Body Strut to the Rear Ferrule while keeping the Tail Stiffener inside the Tail (Diagram B).

Keep the Tail Stiffener inside the Tail as you rotate the Body Sleeve clockwise. The Main Internal Body Strut aligns with the Rear Ferrule at the rear of the Bike Frame Strut Assembly.

Unicorn Bike Spinner body sleeve, rear ferrule, basket sleeve and Velcro tabs
B: Connect the Body Sleeve and attach the Basket Sleeve.

Step 3: Attach the basket sleeve and Velcro tabs

Attach the Basket Sleeve to the front of the Bike Frame Strut Assembly (Diagram B). Then, attach all Velcro Tabs on the inside of the Body Sleeve and the Basket Sleeve to the corresponding Velcro Tabs on the Bike Frame Strut Assembly (Diagram B).

The Basket Sleeve sits at the front of the Bike Frame Strut Assembly. Match the Velcro Tabs inside the Body Sleeve and Basket Sleeve to the corresponding tabs on the frame.

Step 4: Install the axles

Unscrew the threaded Axle Lock Nuts. Then, slide one of the Axles onto the rear axle fitting. The Axle can point either to the right or left but not to the top or bottom, since this is where the Spinner Wheel will sit. Replace the threaded Axle Lock Nut and tighten. Repeat with the front axle fitting, making sure the Axle is pointed the same direction as the rear axle. (Diagram C)

Each Axle sticks out sideways from its fitting so the Spinner Wheel has a place to sit. Point the front Axle the same way as the rear Axle before tightening the Axle Lock Nut.

Unicorn Bike Spinner Axle and Axle Lock Nut installed on the strut assembly
C: Install and tighten the Axles.

Step 5: Add the spinner wheels

Slide Spinner Wheel and Washers onto Axle. The Washers should be placed on either side of the Wheel. Tap Axle Caps onto ends of the Axles using a mallet or piece of wood. (Diagram D)

The order shown is Washer, Spinner Wheel, then Washer on the Spinner Axle. After the wheel and washers are on, the Axle Cap goes onto the end of the Axle.

Unicorn Bike Spinner wheel with washers on each side and an axle cap
D: Install the Spinner Wheel, Washers and Axle Cap.

Step 6: Set up the support pole

Drive the Ground Stake into ground and insert the non-ferruled end of the Support Pole into the Ground Stake. Insert the Upper Pole Section of your completed Unicorn Bike Spinner into the Ferrule on top of the Support Pole. (Diagram E)

The Support Pole stands in the Ground Stake with the Ferrule at the top. Lower the completed Unicorn Bike Spinner so its Upper Pole Section goes into the Ferrule.

Unicorn Bike Spinner mounted on the support pole and ground stake
E: Place the spinner on the Support Pole and Ground Stake.

Care note

Please note: Although your Bicycle Spinner is constructed with UV resistant SunTex™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manual

Unicorn Bike Spinner Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.