This guide covers assembly for Premier vehicle spinners that use the same support pole, spinner axle, wheel, and ground stake setup. It applies to the tractor, train, fire truck, woody, horse and buggy, and golf cart designs listed below.

Applies to: Premier 17 in. to 26 in. vehicle spinners. See the 8 products this guide covers.

Have a Modern Tractor, International Harvester, Allis Chalmers, Sport Pick-Up, VW Hippie Mobile, B&O Tender, or 23 or 35 in. Golf Cart spinner? Those use different instructions; see the Vehicle Spinner Assembly Instructions for tractors, trucks and golf carts.

Spinner specifications

Product Theme Size (W x L)
17 in. Golf Cart Spinner Vehicle / Golf Cart 17 in. x 15 in.
21 in. Fire Truck Spinner Vehicle / Fire Truck 21 in. x 9 in.
21 in. Steam Engine Spinner Vehicle / Train 21 in. x 11.5 in.
21 in. Woody Spinner Vehicle / Surf 21 in. x 11 in.
22 in. Uncle Sam on a Tractor Spinner Vehicle / Tractor 22 in. x 18.25 in.
23 in. Old Tractor Spinner - Green or Red Vehicle / Tractor 23 in. x 16 in.
26 in. Horse & Buggy Spinner Vehicle / Horse & Buggy 25.5 in. x 14.5 in.

Assembly

Step 1: Open the Velcro seam

Remove your spinner from the package. Open the Velcro seam along the bottom of the spinner.

The Velcro seam runs along the lower edge of the spinner body. Opening it gives access to the Star Lock Hub area for the Upper Support Pole.

Vehicle Spinner internal strut with Star Lock Hub, Velcro seam, and Upper Support Pole
Diagram A: Internal strut assembly and Upper Support Pole

Step 2: Lock the upper support pole into the hub

Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and cannot be removed. Close Velcro Seam. Completed internal Strut Assembly should match Diagram A.

The plastic tip of the Upper Support Pole goes into the Star Lock Hub inside the opened seam. When it is assembled, the Upper Support Pole extends down from the body and the internal strut assembly lies along the bottom of the spinner.

Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.

Step 3: Attach the spinner axles

Slide the Spinner Axles onto the Wheel Strut Assemblies. Tighten knobs on the "T" Joints to hold the Axles to the Struts. (Diagram B)

Each Spinner Axle is held by a "T" Joint with a knob. Slide the "T" Joint onto the Wheel Strut Assembly first, then tighten the knob to hold the axle in place.

Vehicle Spinner axle sliding onto the strut assembly with the T Joint knob
Diagram B: Spinner Axle and "T" Joint

Step 4: Install the spinner wheels

Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of the spinner should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams C and D.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (Diagram C)

Install two Spinner Wheels on each Spinner Axle. The Axle Cap goes on the uncapped end after the wheels are in place.

Vehicle Spinner wheels on a Spinner Axle with Axle Cap and opposite spin arrows
Diagram C: Spinner Wheels and Axle Cap
Vehicle Spinner mounted on the Ground Stake with upper and lower support poles
Diagram D: Ground Stake and support poles

Step 5: Set the spinner on the ground stake

Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole into the Ground Stake. Insert Upper Pole of assembled spinner into the ferrule. (Diagram D)

The non-ferruled end of the Lower Support Pole goes down into the Ground Stake. The ferrule stays at the top of the Lower Support Pole, between the Lower Support Pole and the Upper Support Pole.

Care note

It is recommended that you take your spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.