This guide covers the shared assembly steps for Premier vehicle spinners. It applies to the tractor, golf cart, train tender, VW Hippie Mobile, and Sport Pick-Up Truck designs listed below.
Applies to: 23 in. and 35 in. Golf Cart, Modern Tractor, 38 in. Tractor, VW Hippie Mobile, Allis Chalmers, B&O Tender, International Harvester, and Sport Pick-Up Truck spinners. See the 10 products this guide covers.
Have the Steam Engine, Fire Truck, Woody, Horse & Buggy, 23 in. Old Tractor, Uncle Sam Tractor or 17 in. Golf Cart spinner? Those use different instructions; see the Vehicle Spinner Assembly Instructions for them.
Sizes
| Product | Size (W x L) |
|---|---|
| 23 in. Golf Cart Spinner | 23 in. x 20 in. |
| 24 in. Modern Tractor Spinner - Green / Red | 24 in. x 20 in. |
| 35 in. Golf Cart Spinner | 35 in. x 29.5 in. |
| 38 in. Tractor Spinner - Green | 38 in. x 27 in. |
| 38 in. VW Hippie Mobile Spinner | 38 in. x 17.5 in. |
| Allis Chalmers Tractor Spinner | 43 in. x 28 in. |
| B&O Tender Spinner | 20 in. x 16 in. |
| International Harvester Tractor Spinner | 43 in. x 27.5 in. |
| Sport Pick-Up Truck Spinner | 41 in. x 27.5 in. |
Assembly
Step 1: Connect the strut assembly sections
The Strut Assembly of your spinner is shipped in three sections. Connect Center Rods of the Rear Strut Assembly and the Front Strut Assembly to the Center Rod of the Center Strut Assembly as shown. (diagram A)
The Rear Strut Assembly and Front Strut Assembly connect into opposite sides of the Center Strut Assembly. When finished, the completed internal strut assembly should have all parts connected as shown.


Step 2: Insert the completed strut assembly
Open Velcro straps and insert completed Strut Assembly into bottom of Body Sleeve as shown. Reclose Velcro straps. (diagram B) For Modern Tractor, 38 in. Tractor, International Harvester/Farmall Tractor, Allis Chalmers, 35 in. Golf Cart, and 23 in. Golf Cart, make sure the internal body struts connect to the Strut Assembly. For Allis Chalmers, insert the remaining stiffener and connect to the Strut Assembly. For 35 in. Golf Cart, insert the two remaining stiffeners and connect to the Strut Assembly.
The arrows show the completed Strut Assembly moving upward into the Body Sleeve. The Internal Body Struts are inside the body, and the completed Strut Assembly is below them.
Tip: For B&O Tender, Hippie Mobile, and Sport Pick-Up Truck, reclose the Velcro straps after inserting the completed Strut Assembly; those manuals do not include the internal strut connection sentence. Allis Chalmers: insert remaining stiffener and connect to Strut Assembly; the diagram notes the Velcro opening to insert the Gas Tank Strut. 35 in. Golf Cart: insert the two remaining stiffeners and connect to the Strut Assembly.

Step 3: Install the rear spinner axle
Take one of the Spinner Axles and slide it onto the Rear Strut Assembly at back of the Body. Tighten the knob on the "T" Joint to hold the Axles to the Struts. (diagram C)
The Spinner Axle runs through the "T" Joint, with the knob on the side of the joint. The diagram text gives the order: first slide the Spinner Axle onto the Strut Assembly, second tighten the knob on the "T" Joint.

Step 4: Add two spinner wheels to the rear axle
Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of the spinner should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams D and E.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (diagram D)
One Axle Cap goes on one end of the Spinner Axle, and the second Axle Cap goes on the uncapped end after the wheels are on. Diagram D marks that wheels on the same axle should spin in opposite directions.

Step 5: Assemble the front spinner
Repeat Step 4 using second Spinner Axle and the two remaining Spinner Wheels to assemble the front Spinner.
Use the second Spinner Axle with the two remaining Spinner Wheels. After assembly, the Spinner Wheels on the same side of the vehicle should spin in the same direction, as shown in diagram E.

Step 6: Set the spinner on the support pole
Pound Ground Stake into ground and insert non-ferruled end of Support Pole into Ground Stake. Insert Upper Pole Section of completed spinner into ferrule on top of Support Pole. (diagram E)
The Support Pole is labeled with the ferrule at the top and the Ground Stake at the bottom. The completed spinner lowers onto the ferrule from above.
Care and weather note
Although your spinner is constructed with UV resistant SunTex™ or SolarMax™ fabric, it is recommended that you take it inside during storms and harsh weather to preserve its durability.
Tip: Use SunTex™ when following the Modern Tractor, B&O Tender, Hippie Mobile, and 23 in. Golf Cart manuals; use SolarMax™ when following the other manuals.
Products this guide covers
24 in. Modern Tractor Spinner - Green
24 in. Modern Tractor Spinner - Red
35 in. Golf Cart Spinner
38 in. Tractor Spinner - Green
38 in. VW Hippie Mobile Spinner
B&O Tender Spinner
International Harvester Tractor Spinner
Sport Pick-Up Truck Spinner
23 in. Golf Cart Spinner
Allis Chalmers Tractor Spinner
Download the original manuals
Premier prints a manual for each design; the steps are the same apart from the differences noted above.


Share:
Vehicle Spinner Assembly Instructions: Steam Engine, Fire Truck and Woody
VW Hippie Mobile and Beetle Spinner Assembly Instructions