This guide covers assembly for Premier's Volkswagen vehicle spinners in the 22 in. VW Hippie Mobile and 24 in. VW Beetle designs. The steps show how to open the body, install the support pole, add the spinner axles and wheels, and mount the spinner on the ground stake.
Applies to: 22 in. VW Hippie Mobile Spinner and 24 in. VW Beetle Spinner designs. See the 5 products this guide covers.
Product sizes
| Model | Size (W x L) |
|---|---|
| 22 in. Hippie Mobile Spinner | 22 in. x 10.5 in. |
| 24 in. VW Beetle Spinner | 24 in. x 10 in. |
Assembly
Step 1: Open the Velcro seam
Remove your VW Hippie Mobile or VW Beetle Spinner from the package. Open the Velcro seam along the bottom of the Hippie Mobile or Beetle.
The Velcro seam runs along the bottom edge of the vehicle body. Opening this seam gives access to the internal strut assembly and the Star Lock Hub.

Step 2: Lock the upper support pole into the hub
Slide the narrow, plastic tipped end of the Upper Support Pole into the Star Lock Hub. Push down on the hub until the Support Pole locks into place and cannot be removed. Close Velcro Seam. Completed internal Strut Assembly should match Diagram A.
The Star Lock Hub is inside the vehicle body at the center of the internal strut assembly. The plastic tip of the Upper Support Pole goes up into the hub, and the pole extends down from the bottom of the vehicle when it is in place.
Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub.
Step 3: Attach the spinner axles
Slide the Spinner Axles onto the Wheel Strut Assemblies. Tighten knobs on the "T" Joints to hold the Axles to the Struts. (Diagram B)
Each Spinner Axle passes through a "T" Joint at the bottom of a Wheel Strut Assembly. After the axle is in place, tighten the knob on the "T" Joint so the axle is held to the strut.

Step 4: Add the spinner wheels and axle caps
Take one of the four Spinner Wheels and slide it onto one of the two Spinner Axles. Slide second Spinner Wheel onto Spinner Axle. (Note: Spinner Wheels on same side of the Hippie Mobile or Beetle should spin in same direction and Spinner Wheels on same axle should spin in opposite directions. Before putting second Axle Cap into place, make sure wheels spin as shown in diagrams C and D.) Pound second Axle Cap onto uncapped end of Spinner Axle using a mallet or piece of wood. (Diagram C)
The axle cap goes on the end of the Spinner Axle after the wheels are placed on that axle. When the wheels are oriented correctly, wheels on the same side spin the same direction, and wheels on the same axle spin in opposite directions.


Step 5: Install the support pole and ground stake
Drive Ground Stake into ground and insert the non-ferruled end of the Lower Support Pole into the Ground Stake. Insert Upper Pole of assembled Hippie Mobile or Beetle Spinner into the ferrule. (Diagram D)
The Lower Support Pole sits in the Ground Stake, and the ferrule is the connector above it. The Upper Support Pole from the assembled spinner slides down into the ferrule.
Care note
Please note: it is recommended that you take your VW Hippie Mobile or VW Beetle Spinner inside during storms and harsh weather to preserve its durability.
Products this guide covers
22 in. Hippie Mobile Spinner - Blue
22 in. Hippie Mobile Spinner - Orange
22 in. Hippie Mobile Spinner - Red
24 in. VW Beetle Spinner - Green
24 in. VW Beetle Spinner - Red
Download the original manuals
Premier prints a manual for each design; the steps are the same apart from the differences noted above.


Share:
Vehicle Spinner Assembly Instructions: Tractors, Trucks and Golf Carts
WhirliGig Spinner Assembly Instructions