This guide covers assembly for the Premier WhirliGig Spinner designs listed below. The steps show how to set the spinner axle, install the spinner sets, add the support pole and place the spinner in the ground stake.

Applies to: Snowy Owl and Zombie WhirliGig Spinners. See the 2 products this guide covers.

Product sizes

Product Size (W x L)
WhirliGig Spinner - Snowy Owl 14 in. x 22 in.
28 in. WhirliGig Spinner - Zombie 10 in. x 28 in.

Assembly

Step 1: Position the spinner axle

Loosen the Thumb Screw on the Main Frame and slide the Spinner Axle as far as possible through the Frame. Make sure that the three stops on the Axle are on the same side of the WhirliGig Body as the Thumb Screw. This should make the ends of the Axle equally far from the WhirliGig Body. Tighten Thumb Screw. (Diagram A)

The inset marks the axle spacing as 3.5" on each side. Keep the Thumb Screw and the three Stops together on the same side of the Main Frame before tightening.

WhirliGig Spinner axle with stops, thumb screw, washer, spinner set and end cap
A and B: Spinner axle position and first spinner set parts.

Step 2: Install the spinner sets

Set the Spacer, two Washers and one spinner set aside. Slide one Washer onto the side of the Axle with the Stops. Decide which way you want the arms or wings to face and slide one set onto the Axle followed by the remaining Washer. Carefully pound the End Cap onto the Axle. Repeat with the remaining parts on the other side of the Axle, making sure to place the Spacer closest to the WhirliGig Body. (Diagrams B & C)

On the side with the Stops, the parts go on in this order: Washer, Spinner Set, Washer, then End Cap. On the other side, the parts go on in this order from the WhirliGig Body outward: Spacer, Washer, Spinner Set, Washer, then End Cap.

WhirliGig Spinner spacer, washer, end cap and support pole with Star Lock Hub
C: Spacer, spinner set and support pole into the Star Lock Hub.

Step 3: Attach the support pole

Slide the narrow, plastic tipped end of the Support Pole into the Star Lock Hub by passing it through the opening in the fabric. Insert your hand into the opening in the fabric on the side of the WhirliGig Body to help guide the pole. Push down on the hub until the Support Pole locks into place and can not be removed. (Diagram C & D)

The narrow plastic tip of the Support Pole goes up into the Star Lock Hub inside the body. Use the Assembly Access Opening on the side to guide the support pole into the hub hole.

Tip: To make insertion process easier, place bottom of Support Pole on a hard, flat surface and push down on Star Lock Hub. Snowy Owl: the support pole opening is at the feet of the bird and is indicated by a removable label “Insert Stake Here”; Zombie: the support pole should be inserted through the opening in the leg of the zombie.

WhirliGig Spinner body with assembly access opening and support pole
D: Access opening and support pole insertion through the body.

Step 4: Place the spinner in the ground stake

Drive Ground Stake into ground and insert the Support Pole of assembled WhirliGig Spinner into the ground stake. (Diagram D)

The Support Pole slides down into the Ground Stake after the stake is in the ground. The assembled WhirliGig sits above the Ground Stake on the Support Pole.

WhirliGig Spinner on support pole inserted into ground stake
E: Support pole inserted into the ground stake.

Care in harsh weather

Please note: It is recommended that you take your WhirliGig Spinner inside during storms and harsh weather to preserve its durability.

Products this guide covers

Download the original manuals

Premier prints a manual for each design; the steps are the same apart from the differences noted above.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.