This guide covers assembly, bridle adjustment, line setup, launching, control, landing, and wind guidance for the Wolf NG sport kite. It applies to the Wolf NG Sport Kite - White Rainbow.

Applies to: Wolf NG Sport Kite - White Rainbow. See the 1 products this guide covers.

Specs

Model Size Wind range Line Frame Fabric Weight
Wolf NG Sport Kite - White Rainbow 80.5 x 31 in. / 204.5 x 79 cm. 4 ~ 25 mph Includes 150 lb. Test Spectra Line with Winder & S. Wrapped Carbon & 2400 Fiberglass Ripstop Polyester 9 oz. / 255 gm.

Names of Parts

Wolf NG kite with labeled parts including bridle, spreaders, standoffs, and leading edge
Names of Parts.
  1. Nose/Nose Piece
  2. Center Spine
  3. Upper Connector
  4. Leading Edge
  5. YoYo Stop
  6. Lower Connector
  7. Standoff Holder
  8. Standoff
  9. Tow Point Loop
  10. Center ‘T’ Fitting
  11. Tail
  12. Bottom Leg of Bridle
  13. Bridle Out-Haul
  14. Bungee
  15. Wing Tip
  16. Bottom Spreader
  17. Top Leg of Bridle
  18. Sail
  19. Top Spreader

Safety First

Be sure to avoid flying near cars, people, power lines and airports. Stunt kites can move at high speeds and are capable of inflicting damage on people and property. Both the kite and flying lines represent potential hazards. The kite and line can hit or cut with high force while moving at high speeds. Use your stunt kite with extreme care. Flying safely is your sole responsibility.

Assembly Instructions

Step 1: Lay out the kite

Remove the kite out of the bag. Lay the kite out and extend the Sail.

The sail is spread into its full shape with the nose at the top and the wing tips extended to each side. The center spine runs down the middle of the sail.

Wolf NG kite laid out with the sail extended
Step 1: Sail extended.

Step 2: Tension the wing tip bungees

Remove the End Cap from the Wing Tip and tension the Bungee over the Nock with the first knot. Replace End Cap and repeat with other Wing Tip.

At each wing tip, the end cap sits at the outer end of the wing tip. The bungee loops over the nock before you replace the end cap.

Wolf NG wing tip with bungee, nock, and end cap
Step 2: Wing tip bungee.

Step 3: Insert the lower cross struts

Stick the Lower Cross struts into the Center T-Fitting, making sure the Bridle is not tangled around the struts.

The two lower cross struts meet at the Center ‘T’ Fitting on the center spine. The bridle should stay clear of the struts instead of wrapping around them.

Wolf NG lower cross struts meeting at the Center T-Fitting
Step 3: Lower cross struts at the Center T-Fitting.

Step 4: Insert the upper cross strut

Insert the Upper Cross Strut into the Top Connectors.

The Top Connectors are the fittings on the leading edges near the upper part of the kite, as named in the parts diagram.

Step 5: Install the standoffs and check the bridle

Insert Standoffs into Standoff Holders. Slide the Standoff Holders along the Lower Cross Strut to make sure they are directly behind the Standoffs and the Standoffs are perpendicular to the Lower Cross Strut. Lift the assembled Wolf NG off the ground by the kite’s two Tow Points and make sure the bridle is not tangled or twisted underneath a Cross Strut. The bridle attachment points should come directly off the knots on the kite’s right and left Leading Edges and the Center Spine.

The standoff holders are on the lower cross strut, and the standoffs run from the sail to those holders. Use the two Tow Point Loops to lift the kite for the bridle check.

Bridle and Line Setup

Bridle Adjustment at Tow Point

Your bridle has been factory set and marked for your convenience. If the tow point loop has shifted it can be corrected. To make changes, pull top leg and bottom leg to open the larks head knot. Slide the tow point above or below the mark. For less pull and more height, move the tow point towards the nose. This is good for faster climbing in light winds. For more pull and fast turns, move the tow point towards the tail. Make small changes, 1/8” makes a big difference in flying performance.

Fast Bridle Adjustment at Upper Cross Strut

For quick bridle adjustments your Wolf NG comes with a simple adjustable upper cross strut hook up that can be easily changed for different wind conditions and flying characteristics.

The upper bridle is at the upper cross strut hook up with knots positioned closer to and farther from the kite frame.

Wolf NG upper bridle connected to knots near the upper cross strut
Fast Bridle Adjustment at Upper Cross Strut.

For faster climb in lighter winds, connect the upper bridle to the knots closer to the kite frame. For faster turning in higher winds connect the upper bridle to the knots farther from the kite frame.

Connecting Flight Lines

Your kite is now fully assembled and ready to fly. All you need to do is attach your flying lines and wrist straps. Attach flying lines using a larks head or cinch type knot.

The flying line attaches at the tow point where the bridle legs lead to the Top Connector, Center T, and Bottom Connector.

Wolf NG flying line attached to bridle legs for top connector, Center T, and bottom connector
Connecting Flight Lines.

Pre-Flight

Place your Wolf NG on the ground with the kite’s back against the ground. After hooking your lines up to the bridle points, unroll the lines all the way to the end. Hold the flying straps together and make sure your lines are even. It is important that whenever you fly your kite that the two flying lines are exactly the same length. If your right line is longer than your left line or vice versa, your kite will be hard to control. Your lines come pre-tied at the factory to even lengths. If they have stretched or are different lengths, simply shorten the longer line to match the shorter line.

Learning to Fly

Step 1: Set the lines and helper position

Lines must be out and adjusted to equal lengths before launching. Make sure the person holding the kite is behind it and pointing the nose skyward. Keep your hands forward and parallel just before launch.

Wolf NG helper behind the kite with nose skyward and flyer holding lines forward
Step 1: Lines even before launch.

Step 2: Launch with equal tension

Wind must be at flyer’s back. To take off, tell your friend to release the kite. At the same time pull back on both lines with equal tension to launch the kite. Immediately return both hands forward.

Wolf NG launch with wind at the flyer’s back and both lines pulled evenly
Step 2: Launch with wind at the flyer’s back.

Solo Launching

With first flights it is easiest to have a helper toss the kite into the air. When flying alone stake your handles or straps to the ground with an old screw driver or tent stake or anything that you can push into the ground. With the lines completely unwound attach your kite. With the lines anchored and under tension, the kite will stand on its wing tips. Tilt the nose of the kite back 45 degrees so the kite doesn’t accidentally self launch.

To launch the kite, pull both lines until the kite stands up straight. Then pull back both lines with equal tension and the kite will launch straight into the sky. Remember to return both hands forward.

Control

On your first launch, keep your hands next to each other and let your kite ascend as high as possible. If your kite wanders to one side, make corrections by pulling on the opposite control handle. A stunt kite turns towards the same direction it is pulled: Pull right - the kite turns right, pull left the kite turns left. As a beginner, concentrate on steering towards the sky and maintaining plenty of altitude before doing complex stunts.

The most common problem a beginner has is over controlling their kite. Only a few inches of pull is needed for maneuvering. If you continue to pull to one side, your kite will make a loop. The further you pull back the line, the tighter the loop will be. At any point in the loop or turn, you can even out your hands and the kite will continue in the direction the nose is pointing.

After doing loops, your control lines will be twisted. This may seem troublesome, but don’t worry, you still have control of your kite. To untwist, simply fly loops in the opposite direction.

Control responses

Pull Left: Kite turns left. Hands Even: Kite flies straight in the same direction it is pointing. Pull Right: Kite turns right.

With both hands even, the kite flies straight in the same direction its nose is pointing.

Wolf NG control responses for pull left, hands even, and pull right
Control: Pull left, hands even, pull right.

Maneuvering in the Wind Window

The Wind Window is an area of the sky where sport kites maneuver. The Window is shaped like a half dome. The size of the Window changes with the wind speed. Higher winds produce larger Windows. Your kite will react differently in various parts of the Window. The Power Zone is where your kite will pull the most and have the most speed. This is where you will have the most success launching your kite. On the Edge the kite is angled away from the direct wind. This lowers the speed and pull of the kite and makes landings easier. The extreme edge is the point where the kite can not move forward anymore.

The wind window forms a half dome in front of you, with wind coming from behind you. The Power Zone is near the middle of the window, and the Edge is around the outside of the window.

Wolf NG wind window with Power Zone, Edge areas, and wind from behind the flyer
Wind Window.

In lighter winds your kite becomes a victim of gravity and sinks to the ground. In higher winds your kite can hover on the edge and retain its position in the sky.

Wind Window Areas

  • Power Zone: Most speed.
  • Power Zone: Most pull.
  • Power Zone: Fastest response.
  • Power Zone: Easiest area to launch.
  • Edge: Slower speed.
  • Edge: Less pull.
  • Edge: Slower response.
  • Edge: Easiest area to land.

Landing

You will soon notice that as the kite flies to the edge of the Window, it slows down and eventually stalls. Maneuver the kite to the outermost edge about a foot off the ground and run toward the kite while throwing your arms forward. Your lines will go slack and the kite will gently land.

For an advanced maneuver, try landing your kite on its wing tips. When your kite is about a foot off the ground, rotate the nose skyward and run forward, keeping your hands in front and the line equal. The kite will lose wind and land on its wing tips. You are now ready to relaunch.

Where to Fly

Find a flying field that is large, flat and wide open. Look for areas where there are no large obstructions interrupting smooth flowing wind. Obstructions, such as trees or buildings, add turbulence and reduce wind speed near ground levels. Determine the wind’s direction by throwing grass or sand into the air. The direction of the wind will determine where your flight area will be and where you will set up the kite. Winds from 10-14 M.P.H. are ideal for learning how to fly your Wolf NG Sport Kite.

Beaufort Scale

Wind Speed Description Specifications for use on Land
0-1 Calm Calm; smoke rises vertical.
1-3 Light Air Direction of wind shown by smoke drift, but not by wind vanes.
4-7 Light Breeze Wind felt on face; leaves rustle; ordinary vanes moved by wind.
8-12 Gentle Breeze Leaves and small twigs in constant motion; wind extends light flag.
13-18 Moderate Breeze Raises dust and loose paper; small branches are moved.
19-24 Fresh Breeze Small trees and leaves begin to sway; crested wavelets form on inland waters.
25-31 Strong Breeze Large branches in motion; whistling heard in telegraph wires; umbrellas used with difficulty.

Optimum Wind Conditions

Wolf NG optimum wind conditions chart from light breeze through fresh breeze
Optimum Wind Conditions for Wolf NG Kites.

Best wind for Wolf NG kites: 4-25 mph. Note: Wind Conditions aloft may vary considerably from those found near ground level.

Products this guide covers

Download the original manual

Wolf NG Assembly Instructions (PDF)

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.